Clarke 2090908 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

Clarke 2090908 Скачать руководство пользователя страница 11

11

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

CLEAN THE COMPRESSOR AIR FILTER (MONTHLY)

The air filter must be examined monthly or more often in dusty conditions.

1. Remove the securing wingnut.

2. Lift off the top cover to expose the

filter element.

3. Undo the second wingnut holding

the filter in place and remove the
filter.

4. If necessary, the outer sponge

filter can be carefully cleaned in
warm soapy water.

5. Rinse and let the sponge filter dry

completely before refitting.

6. Clean the main filter element

using a soft brush or a vacuum
cleaner.

• If the main filter element is

damaged it must be replaced.

7. Refit the filters and replace the

cover, securing with the wingnuts
as above.

CHECK THE ENGINE INTAKE FILTER (3 MONTHLY/25 HOURS)

1. Unscrew the engine air intake filter

assembly and prize off the outer
cover by releasing the three small
tabs around the perimeter to
check the filter for cleanliness.

2. Tap the filter against a hard

surface to dislodge loose dirt or
blow through with compressed air.
Take care when using
compressed air and use PPE if
appropriate.

«
...
9
10
11
12
13
...
»

Содержание 2090908





















Отзывы:

Нет отзывов