Clarke 2090908 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

Clarke 2090908 Скачать руководство пользователя страница 13

13

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

5. Check the spark plug gap (a) with

a feeler gauge. It should be
between 0.6 and 0.7 mm.

• Adjust if necessary by carefully

bending the electrode.

NOTE:

Spark plugs are available

from your CLARKE dealer.

6. Re-fit the spark plug taking care

not to cross thread it and tighten
half a turn after the spark plug
seats to compress the washer.

7. Refit the spark plug cap/lead.

EVERY 2 YEARS/250 HOURS

1. Carry out the oil changes.

2. Replace the spark plug and air filter.

3. Request your CLARKE dealer to replace fuel lines.

MISCELLANEOUS SPARE COMPONENTS

No

Description

Part No

1

Pump Assembly MK238 Complete

1370005

2

Honda Engine (type GP160HQX3) 5HP

8000002

3

Drain Cock

2000221

4

Pressure Gauge

2000171

5

Safety Valve

2000191

6

Manifold 4-way

FN011276000

7

Rubber Foot

FN116011006

8

Regulator

FN347026000

9

Spark Plug

NGK BPR6ES

10

Engine Air Filter Set

HS17210ZE1505

11

Recoil Starter Assembly

HS28400ZDK003

12

Starter Pull-cord

HS28462ZDK003

«
...
11
12
13
14
15
...
»

Содержание 2090908





















Отзывы:

Нет отзывов