manualshive.com logo in svg

Clarke 2090908, Инструкция по эксплуатации и обслуживанию, Страница: 3 / 20

Поделиться
Скачать
Clarke 2090908 Скачать руководство пользователя страница 3

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

GENERAL SAFETY PRECAUTIONS

Before using your compressor, read and pay attention to the following safety 
guidelines.

1. Make sure that all persons using the compressor have read and fully 

understand these operating instructions and had any necessary training

2. Compressed air is dangerous. DO NOT point a jet of air at persons or 

animals or discharge compressed air against the skin.

3. Repairs must only be carried out by a qualified engineer. If problems occur, 

contact your CLARKE dealer.

4. Before carrying out any maintenance, make sure that the pressure is 

released from the air receiver.

5. DO NOT leave pressure in the air receiver overnight or when transporting.

6. DO NOT adjust or tamper with the safety valve. The maximum pressure is 

set at the factory.

7. DO NOT operate in wet or damp conditions. Keep the compressor dry at all 

times. Similarly, clean air will allow the compressor to work efficiently. Do 
not use in dusty or otherwise dirty locations.

8. Some metal parts can become hot during operation. DO NOT touch these 

until the compressor has cooled down.

9. ALWAYS set the pressure regulator to the recommended setting for the air 

tool being used.

10. When spraying flammable materials e.g. cellulose paint, ensure that there 

is sufficient ventilation and keep clear of any source of ignition.

11. DO NOT use this compressor in explosive atmospheres.

12. DO NOT operate this compressor in a confined space unless additional 

ventilation is provided.

13. Before spraying any material always consult paint manufacturers 

instructions for safety and usage.

14. Wear PPE such as goggles to protect your eyes from flying particles. Face 

masks will protect you against paint spray and fumes.

15. This compressor will produce noise levels in excess of 70dB(A). Persons 

working near the compressor must be equipped with ear protection.

16. Make sure that air hoses are not kinked or wrapped around the compressor 

and not subjected to strain.

Содержание 2090908





















Отзывы:

Нет отзывов