Citizen CT-D150, Справочник по командам

Страница: 359 / 512

Support
model
CT-S280 CT-S300 CT-S2000 CT-S4000 CT-S251 CT-D150/E351
CT-S281 CT-S310 CT-S801/851 CT-S601/651 CT-P29x series CT-S310II
CT-D151/E651
- 358 -
fn=11: Function 11 Setting Communication Conditions
GS ( E pL pH fn a d1...dk
[Code] <1D>H<28>H<45>H<pL><pH><fn><a><d1>...<dk>
[Range] 3
≤(pL+pH×256)≤65535(0≤pL≤255, 0≤pH≤255)
fn=11
1
≤a≤4 (Not changed in other than specified range)
48
≤d≤57 (Not changed in other than specified range)
1
≤k≤6
[Outline] [The specification which is common to the model]
• Sets the communication conditions of serial interface specified by “a”.
• a=1: Setting baud rate
Baud Rate d1 d2 d3 d4 d5 d6
◎
1200 49(“1”) 50(“2”) 48(“0”) 48(“0”)
- -
2400 50(“2”) 52(“4”) 48(“0”) 48(“0”) - -
4800 52(“4”) 56(“8”) 48(“0”) 48(“0”) - -
▲9600
57(“9”) 54(“6”) 48(“0”) 48(“0”) - -
△
19200 49(“1”) 57(“9”) 50(“2”) 48(“0”) 48(“0”) -
38400 51(“3”) 56(“8”) 52(“4”) 48(“0”) 48(“0”) -
●57600
53(“5”) 55(“7”) 54(“6”) 48(“0”) 48(“0”) -
●115200
49(“1”) 49(“1”) 53(“5”) 50(“2”) 48(“0”) 48(“0”)
◎
---support by
CT-S280 / CT-S281 / CT-S2000 / CT-S4000 / CT-S801(II) / CT-S851(II) / CT-S601(II) / CT-S651(II) /
CT-S310II / CT-S251 / CT-D150 / CT-E351
●---support by
CT-S280 / CT-S2000 / CT-S4000 / CT-S801(II) / CT-S851(II) / CT-S601(II) / CT-S651(II) / CT-S310II / CT-S251 / CT-D150 / CT-E351 / CT-D151 / CT-E651
*
CT-P29x series does not support 115200bps .
△
---Default :
CT-S300 / CT-S310 / CT-S2000(JPN/EUR) / CT-S4000(JPN/EUR)
▲---Default :
CT-S280 / CT-S281 / CT-S2000(USA) / CT-S4000(USA) / CT-S801(II) / CT-S851(II) / CT-S601(II) / CT-S651(II) /
CT-P29x series / CT-S310II / CT-S251 / CT-D150 / CT-E351 / CT-D151 / CT-E651
• a=2: Setting to specified parity
d1 Parity Setting
48 (Default) No parity
49 Odd parity
50 Even parity
• a=3: Setting to specified flow control
d1 Flow Control
48 (Default) DSR/DTR
49 XON/XOFF
• a=4: Setting to specified data length
d1 Setting Data Length
55 7-bit length
56 (Default) 8-bit length
• Operates only in printer function setting mode.
• Which of dip SW or memory SW is used at initialization depends on “Selecting communication condition
setting” of dip SW1-1.