Cisco TX1300 47 Скачать руководство пользователя страница 2

Страница: 2 / 20

2-2

Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide

OL-24695-01

Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version

Assembling the TX1300 47

To assemble the TX1300 47, complete the following steps:

Step 1

Take an inventory of the parts in the shipping carton.

Figure 2-1

shows the carton contents:

Accessory kit (CTS1300-47ACCKIT)

Base (CTS1300-47BASEPED or CTS1300-47BASETETH)

Cabinet (CTS1300-47CABEXTR)

Display (CTS-DISP-47-GEN1)

Camera (CTS1300-47CAMCLST)

Codec (CTS-CODEC-PRI-G2R)

Speaker cover (CTS1300-47SPKCOV)

Light reflector (CTS1300-47AV-PNL)

Microphone (CTS-MIC)

10.

Microphone (CTS-MIC)

11.

Microphone (CTS-MIC)

12.

Cisco TelePresence Touch 12 (CTS-CTRL-DV12-A)

13.

Cabinet cover (CTS1300-47CABCOV)

14.

Seat alignment guides (CTS1300-SAG)

15.

Cable cover (CTS1300-47ACCKIT)

16.

Audio/visual (A/V) panel cover (CTS1300-47AV-CVR)

17.

Camera targets and easel (CTS-CAM-TOOL-G2)

18.

Not used for this configuration (wall-mounted systems only)

Содержание TX1300 47





















Результаты поиска

Содержание TX1300 47

Отзывы:

Похожие инструкции для TX1300 47

Бренды по названию

Популярные бренды

Cisco TX1300 47, Руководство пользователя

Результаты поиска

Содержание TX1300 47

Отзывы:

Похожие инструкции для TX1300 47

Бренды по названию

Популярные бренды