Cisco TX1300 47 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 20

background image

2-4

Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide

OL-24695-01

Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version

Assembling the TX1300 47

Step 2

Remove the base from its packaging, and attach the feet to the base.

For a freestanding system, be sure to use the larger base with the shorter support posts. Compare this
with the base for the wall-mounted system shown in

Figure 3-2

.

Tip

If the system is not level, use the wrench that is provided in the kit to adjust the base feet to level the base.

Figure 2-2

Attaching the Feet to the Base

209313

«
...
2
3
4
5
6
...
»

Содержание TX1300 47





















Отзывы:

Нет отзывов

Похожие инструкции для TX1300 47

Бренд: Camcar Страницы: 2

Бренд: Acer Страницы: 18

Бренд: XGIMI Страницы: 21

Bicycle Accessories

Бренд: Baby Jogger Страницы: 20

Бренд: IFO Страницы: 12

Бренд: Hamilton/Buhl Страницы: 8

Бренд: Harmar Mobility Страницы: 10

Бренд: Salta Страницы: 91

HOIST-A-TOP JL CRANK

Бренд: Lange Originals Страницы: 13

Q.HOME+ ESS HYB G2

Бренд: Qcells Страницы: 2

Southern Series

Бренд: Warmington Страницы: 2

Video 75 Plus Studio

Бренд: Sachtler Страницы: 34

Бренд: Christie Страницы: 57

Бренд: Neuspeed Страницы: 2

Бренд: GROTHE Страницы: 36

USB 3.0 Dual Head Docking Station

Бренд: SIIG Страницы: 12

Бренд: Thunderbike Страницы: 11

Monarch Pass M321

Бренд: Wolfman Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды