Cisco TX1300 47 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 20

background image

2-7

Cisco TelePresence System TX1300 47 Installation, First-Time Setup, and Field-Replaceable Unit Guide

OL-24695-01

Chapter 2 Assembling the Cisco TelePresence System TX1300 47—Freestanding Version

Assembling the TX1300 47

c.

Route the cables for the display (found with the display in box #4) through the slot in the lower
center area of the reflector and the notch at the top of the cabinet.

d.

Remove the protective paper from the outside of the light reflector.

Note

Alternatively, you can remove the paper before you install the light reflector.

Figure 2-5

Attaching the End Caps and Light Reflector to the Cabinet and Removing the Protective Paper

208408

a

b

c

d

«
...
5
6
7
8
9
...
»

Содержание TX1300 47





















Отзывы:

Нет отзывов

Похожие инструкции для TX1300 47

Бренд: DAPU Страницы: 4

Бренд: Navitar Страницы: 42

Бренд: Barco Страницы: 108

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 143

Бренд: Barco Страницы: 154

Бренд: Barco Страницы: 193

Event Master E2

Бренд: Barco Страницы: 307

Бренд: Barco Страницы: 85

Бренд: Barco Страницы: 6

MES ACURAS HEAD

Бренд: Barco Страницы: 131

Бренд: M-S Cash Drawer Страницы: 2

Бренд: M-S Cash Drawer Страницы: 2

Бренд: Oben Страницы: 12

Бренд: OBH Nordica Страницы: 20

Бренд: Rally Pack Страницы: 2

Бренд: rako Страницы: 3

6130N - Phaser Color Laser Printer

Бренд: Xerox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды