Cisco NCS 1002 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 68

background image

=============================== ================================================

Field Programmable Device Package

================================================

Req

SW

Min Req

Min Req

Card Type

FPD Description

Reload

Ver

SW Ver

Board Ver

=================== ========================== ====== ======= ======== =========
NCS1002

CTRL_BKP_LOW

YES

2.23

2.23

0.1

CTRL_FPGA_LOW

YES

2.23

2.23

0.1

--------------------------------------------------------------------------------
NCS1002

CTRL_BKP_UP

YES

2.23

2.23

0.1

CTRL_FPGA_UP

YES

2.23

2.23

0.1

NCS1002--RP

BIOS_Backup

YES

14.00

14.00

0.1

BIOS_Primary

YES

14.00

14.00

0.1

Daisy_Duke_BKP

YES

0.15

0.15

0.1

Daisy_Duke_FPGA

YES

0.17

0.17

0.1

--------------------------------------------------------------------------------

Upgrade all the FPDs using the

upgrade hw-module location all fpd all

command in the Cisco IOS XR

EXEC mode. After an upgrade is completed, the Status column shows RLOAD REQ if the software requires
reload.

If Reload is Required

If the FPGA location is 0/RP0, use the

admin hw-module location 0/RP0 reload

command. This command

reboots only the CPU. As a result, traffic is not impacted. If the FPGA location is 0/0, use the

admin hw-module

location all reload

command. This command reboots the chassis. As a result, traffic is impacted. After the

reload is completed, the new FPGA runs the current version.

If Firmware Upgrade Fails

If the firmware upgrade fails, use the

show logging

command to view the details and upgrade the firmware

again using the above commands.

Notes for Release 6.1.2

NCS 1002 uses signed images from R6.1.2. Hence, the firmware must be upgraded to identify the signed
images. When the user needs to use the MACsec feature and upgrades from R6.0.1 to 6.1.2, the control FPGA
(CTRL_BKP_UP, CTRL_BKP_LOW, CTRL_FPGA_UP, and CTRL_FPGA_LOW) must be upgraded to
the latest firmware version provided by R6.1.2.

Verify Management Interface Status

To verify the management interface status, perform the following procedure.

Procedure

show interfaces mgmtEth instance

Displays the management interface configuration.

Example:

RP/0/RP0/CPU0:ios#

show interfaces MgmtEth 0/RP0/CPU0/0

Wed Feb 28 03:30:35.525 UTC

MgmtEth0/RP0/CPU0/0 is up, line protocol is up

Interface state transitions: 1
Hardware is Management Ethernet, address is 501c.bf10.9fc0 (bia 501c.bf10.9fc0)

System Setup and Software Installation Guide for Cisco NCS 1002

27

Perform Preliminary Checks

Verify Management Interface Status

«
...
29
30
31
32
33
...
»

Содержание NCS 1002





































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 1002

Vb-C60 - Ptz Network Camera

Бренд: Canon Страницы: 30

Verizon DSL-2750B

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 38

Бренд: Eaton Страницы: 10

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 7

Maestro E220 Series

Бренд: Lantronix Страницы: 25

Бренд: Xinje Страницы: 76

Бренд: QNO Страницы: 106

Бренд: Face Страницы: 8

Бренд: Lorex Страницы: 186

Бренд: Xilica Audio Design Страницы: 30

Бренд: Baldor Страницы: 34

Emulator MCU Board for 38D5 Group M38D59T-RLFS

Бренд: Renesas Страницы: 4

Бренд: Lanner Страницы: 63

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Бренд: Eaton Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды