Cisco NCS 1002 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 68

background image

What to do next

• After performing a system upgrade, upgrade FPD by using the

upgrade hw-module location all fpd

all

command from the Cisco IOS XR mode. The progress of FPD upgrade process can be monitored

using the

show hw-module fpd

command.

• Reload NCS 1002 if any FPD status is in RLOAD REQ state. If CTRL FPGA is in RLOAD REQ state,

use the

hw-module location all reload

command. If Daisy Duke or BIOS is in RLOAD REQ state, use

the

hw-module location 0/RP0 reload

command.

• Verify the installation using the

install verify packages

command.

• Uninstall the packages or SMUs if their installation causes any issues on the NCS 1002. See

Packages, on page 56

.

ISO images cannot be uninstalled. However, you can perform a system downgrade
by installing an older ISO version.

Note

Uninstall Packages

Complete this task to uninstall a package. All the NCS 1002 functionalities that are part of the uninstalled
package are deactivated. Packages that are added in the XR mode cannot be uninstalled from the System
Admin mode, and vice versa.

Installed ISO images cannot be uninstalled. Also, kernel SMUs that install third party SMU on host, XR mode
and System Admin mode, cannot be uninstalled. However, subsequent installation of ISO image or kernel
SMU overwrites the existing installation.

Note

The workflow for uninstalling a package is shown in this flowchart.

System Setup and Software Installation Guide for Cisco NCS 1002

56

Perform System Upgrade and Install Feature Packages

Uninstall Packages

«
...
58
59
60
61
62
...
»

Содержание NCS 1002





































































Отзывы:

Нет отзывов

Похожие инструкции для NCS 1002

ShareCenter DNS-320L

Бренд: D-Link Страницы: 4

SmartSwitch Router

Бренд: Cabletron Systems Страницы: 338

Бренд: Lattice Semiconductor Страницы: 15

Бренд: Paradyne Страницы: 112

Бренд: Cambium Networks Страницы: 215

Бренд: Opvimus Страницы: 12

Бренд: ZALMAN Страницы: 22

Бренд: ZyXEL Communications Страницы: 79

Бренд: FOR-A Страницы: 2

PXI Terminal Block NI TB-2709

Бренд: National Instruments Страницы: 12

Бренд: Sony Ericsson Страницы: 2

Бренд: Smacq Technologies Страницы: 22

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: Camozzi Страницы: 22

OPTIMA II CNPS10X

Бренд: ZALMAN Страницы: 20

Бренд: Abus Страницы: 98

Бренд: ZyXEL Communications Страницы: 12

Бренд: Intercel Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды