Cisco NCS 1002 Скачать руководство пользователя страница 22

Страница: 22 / 68

--------------------------------------------------------------------------------
0/RP0/CPU0

NCS1K-CNTLR(Active)

IOS XR RUN

NSHUT

a) If the Cisco IOS XR is not operational, no output is shown in the result. In this case, verify the state of

service domain router (SDR) on the node using the

show sdr

command in Cisco IOS XR mode.

The following example shows sample output from the

show sdr

command in Cisco IOS XR mode.

RP/0/RP0/CPU0:ios#

show sdr

Wed Feb 28 03:28:45.845 UTC
Type

NodeName

NodeState

RedState

PartnerName

--------------------------------------------------------------------------------
RP

0/RP0/CPU0

IOS XR RUN

ACTIVE

NONE

NCS1K-CNTLR

0/RP0

OPERATIONAL

N/A

Step 2

admin

Enters System Admin EXEC mode.

Example:

RP/0/RP0/CPU0:ios#

admin

Step 3

show platform

Displays information and status for each node in the system.

Example:

sysadmin-vm:0_RP0#

show platform

Wed Feb

28 03:31:53.672 UTC

Location

Card Type

HW State

SW State

Config State

----------------------------------------------------------------------------
0/0

NCS1002-K9

OPERATIONAL

N/A

NSHUT

0/RP0

NCS1K-CNTLR

OPERATIONAL

NSHUT

0/FT0

NCS1K-FTA

OPERATIONAL

N/A

NSHUT

0/FT1

NCS1K-FTA

OPERATIONAL

N/A

NSHUT

0/FT2

NCS1K-FTA

OPERATIONAL

N/A

NSHUT

Verify that all components of the NCS 1002 are displayed in the result. The software state and the hardware
state must be in the OPERATIONAL state. The various hardware and software states are:

Hardware states:

• OPERATIONAL—Node is operating normally and is fully functional.

• POWERED_ON—Power is on and the node is booting up.

• FAILED—Node is powered on but has experienced some internal failure.

• PRESENT—Node is in the shutdown state.

• OFFLINE—User has changed the node state to OFFLINE. The node is accessible for diagnostics.

Software states:

• OPERATIONAL—Software is operating normally and is fully functional.

• SW_INACTIVE—Software is not completely operational.

• FAILED—Software is operational but the card has experienced some internal failure.

System Setup and Software Installation Guide for Cisco NCS 1002

Perform Preliminary Checks

Verify Status of Hardware Components

Содержание NCS 1002





































































Результаты поиска

Содержание NCS 1002

Отзывы:

Похожие инструкции для NCS 1002

Бренды по названию

Популярные бренды

Cisco NCS 1002, Руководство по настройке системы и установке программного обеспечения

Результаты поиска

Содержание NCS 1002

Отзывы:

Похожие инструкции для NCS 1002

Бренды по названию

Популярные бренды