Cisco DS-C9148S48PK9 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 80

background image

1-12

Cisco MDS 9148S Multilayer Switch Hardware Installation Guide

OL-20185-01

Chapter 1 Product Overview

Supported SFP+ Transceivers

Supported SFP+ Transceivers

The following types of SFP+ transceivers are available from Cisco Systems and are supported on the
Cisco MDS 9148S switch:

•

Cisco MDS 4/8/16-Gbps Fibre Channel SW SFP+, LC: DS-SFP-FC16G-SW

•

Cisco MDS 4/8/16-Gbps Fibre Channel LW SFP+, LC: DS-SFP-FC16G-LW

•

Cisco MDS 2/4/8-Gbps Fibre Channel SW SFP+, LC: DS-SFP-FC8G-SW

•

Cisco MDS 2/4/8-Gbps Fibre Channel LW SFP+, LC: DS-SFP-FC8G-LW

•

Cisco MDS 2/4/8-Gbps Fibre Channel Extended Reach SFP+, LC: DS-SFP-FC8G-ER

•

Cisco MDS 2/4/8-Gbps CWDM Long Distance SFP, LC: DS-CWDM8Gxxxx

•

Cisco MDS 4/8/16-Gbps Fibre Channel LW SFP+, DWDM, SM, DDM, 13 dB, 40 km:
DS-16G-ER-Dxxx

•

Cisco MDS 4/8/16-Gbps Fibre Channel LW SFP+, CWDM, SM, DDM, 13 dB, 40 km:
DS-16G-ER-Cxx

•

Cisco MDS 4/8/16-Gbps Fibre Channel/FICON LW SFP+, DWDM, SM, DDM, 1550nm, 13 dB,
40 km: DS-16G-ER

•

Cisco MDS 2/4/8-Gbps Fibre Channel LW SFP+, DWDM, SM, DDM, 80 km: DS-8G-ZR-Dxxx

•

Cisco MDS 2/4/8-Gbps Fibre Channel LW SFP+, CWDM, SM, DDM, 23dB, 70 km:
DS-8G-ZR-Cxx

•

Cisco MDS 2/4/8-Gbps Fibre Channel LW SFP+, SM, DDM, 80 km: DS-8G-ZR

SFP transceivers are field-replaceable. You can use any combination of SFP transceivers that are
supported by the switch. The only restrictions are that SWL transceivers must be paired with SWL
transceivers, and LWL transceivers with LWL transceivers, and the cable must not exceed the stipulated
cable length for reliable communications.

For the list of supported SFP transceivers, see the

Cisco MDS 9000 Family Release Notes for Cisco MDS

NX-OS Releases

. For more information about a specific Cisco SFP transceiver, see the

“SFP Transceiver

Specifications” section on page 1-4

. SFP transceivers can be ordered separately or with the Cisco MDS

9148S Switch.

Port link

Solid green

Link is up.

Steady flashing
green

Link is up (beacon used to identify port).

1

Intermittent
flashing green

Link is up (traffic on port).

Solid orange

Link is disabled by software.

Flashing orange

A fault condition exists.

1.

The flashing green light turns on automatically when an external loopback is detected that causes the interfaces to be isolated.
The flashing green light overrides the beacon mode configuration. The state of the LED is restored to reflect the beacon mode
configuration after the external loopback is removed.

Table 1-1

Switching Module LEDs (continued)

LED

Status

Description

«
...
16
17
18
19
20
...
»

Содержание DS-C9148S48PK9

















































































Отзывы:

Нет отзывов

Похожие инструкции для DS-C9148S48PK9

Бренд: IDEC Страницы: 5

Бренд: IDEC Страницы: 7

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: FLIR Страницы: 2

Бренд: Attwood Страницы: 2

Бренд: socomec Страницы: 78

Бренд: Metrix Страницы: 12

Бренд: CYP Страницы: 20

Бренд: Versa Technology Страницы: 96

ConferenceHub TA-6500

Бренд: TeleAdapt Страницы: 16

Бренд: TRENDnet Страницы: 2

Бренд: Kramer Страницы: 10

Бренд: Intellinet Страницы: 12

Бренд: Gefen Страницы: 15

Бренд: MTI Страницы: 9

Бренд: MTI Страницы: 10

Бренд: Kramer Страницы: 165

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды