Cisco DS-C9148S48PK9 Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 80

background image

1-56

Cisco MDS 9148S Multilayer Switch Hardware Installation Guide

OL-20185-01

Chapter 1 Technical Specifications

SFP Transceiver Specifications

SFP Transceiver Specifications

The Cisco MDS 9148S switch is compatible with SFP transceivers and cables that have LC connectors.
Each transceiver must match the transceiver on the other end of the cable in terms of wavelength, and
the cable must not exceed the stipulated cable length for reliable communications.

Cisco SFP transceivers provide the uplink interfaces, laser transmit (TX), and laser receive (RX), and
they support 850 to 1610 nm nominal wavelengths, depending upon the transceiver.

Use only Cisco SFP transceivers on the Cisco MDS 9148S switch. Each Cisco SFP transceiver is
encoded with model information that enables the switch to verify that the SFP transceiver meets the
requirements for the switch. For the list of supported SFP transceivers, see the release notes.

For details of SFP transceivers see the data sheet at the following location:

http://www.cisco.com/en/US/prod/collateral/ps4159/ps6409/ps4358/product_data_sheet09186a00801b
c698.html

This section provides the following information:

•

Cisco Fibre Channel SFP+ Transceivers, page 1-56

•

Optical Specifications for Cisco CWDM SFP Transceivers, page 1-60

For information about safety, regulatory, and standards compliance, see the

Regulatory Compliance and

Safety Information for the Cisco MDS 9000 Family

.

Cisco Fibre Channel SFP+ Transceivers

lists the Fibre Channel SFP+ transceivers available through Cisco Systems for the

Cisco MDS 9148S switch.

General Specifications for Cisco Fibre Channel 16 Gbps SFP+ Transceivers

summarizes cabling specifications for 16 Gbps.

Table 1-5

Cisco Fibre Channel SFP + Transceivers for the Cisco MDS 9148S Switch

Part Number

Description

Type

DS-SFP-FC16G-SW

Cisco MDS 4/8/16-Gbps Fibre Channel SW
SFP+, LC

Short wavelength

DS-SFP-FC16G-LW

Cisco MDS 4/8/16-Gbps Fibre Channel LW
SFP+, LC

Long wavelength

DS-SFP-FC8G-SW

Cisco MDS 2/4/8-Gbps Fibre Channel SW
SFP+, LC

Short wavelength

DS-SFP-FC8G-LW

Cisco MDS 2/4/8-Gbps Fibre Channel LW
SFP+, LC

Long wavelength

DS-SFP-FC8G-ER

Cisco MDS 2/4/8-Gbps Fibre Channel
Extended Reach SFP+, LC

Extended Reach

DS-CWDM8Gxxxx

Cisco MDS 2/4/8-Gbps CWDM Long
Distance SFP, LC

Long Distance

«
...
60
61
62
63
64
...
»

Содержание DS-C9148S48PK9

















































































Отзывы:

Нет отзывов

Похожие инструкции для DS-C9148S48PK9

Бренд: B&K Страницы: 28

Бренд: B&K Страницы: 2

Бренд: hager Страницы: 2

Бренд: hager Страницы: 4

Бренд: hager Страницы: 2

Бренд: KELCO Страницы: 4

Бренд: Maipu Страницы: 21

Бренд: Maico Страницы: 56

Бренд: StarTech.com Страницы: 24

Бренд: Crestron Страницы: 36

SICOM3432G Series

Бренд: KYLAND Страницы: 29

Бренд: Milestone pro Страницы: 32

Бренд: A-Neuvideo Страницы: 12

Бренд: Power Ethernet Страницы: 2

Бренд: Voith Страницы: 98

Бренд: Exsys Страницы: 14

Бренд: Ortech Страницы: 3

SUPERHUB QUATTRO

Бренд: Manhattan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды