Cisco DS-C9148S48PK9 Скачать руководство пользователя страница 60

Страница: 60 / 80

1-54

Cisco MDS 9148S Multilayer Switch Hardware Installation Guide

OL-20185-01

Chapter 1 Technical Specifications

Power Specifications

This section includes the following information:

•

General Power Supply Specifications, page 1-54

•

Power Supply Requirements Specifications, page 1-55

•

Connection Guidelines for AC-Powered Systems, page 1-55

General Power Supply Specifications

Table 1-3

lists the specifications for the Cisco MDS 9148S switch AC input power supply.

Weight

19.84 lb (9 kg) (with two fan modules and two power
supplies installed)

Power Supply
(fixed)

300-W AC for each power supply

Part Number: DS-C48S-300AC

Power cord: Notched C15 socket connector connecting to
C16 plug on power supply

100 to 240V AC (10% range)

50 to 60 Hz (nominal)

Airflow

Back to front.

200 linear feet per minute (LFM) through the system and a
maximum of 380 LMDM.

Cisco recommends that you maintain a minimum air space
of 2.5 in. (6.4 cm) between walls and chassis air vents and a
minimum horizontal separation of 6 in. (15.2 cm) between
two chassis to prevent overheating.

Table 1-2

Cisco MDS 9148S Switch Specifications (continued)

Description

Specification

Table 1-3

Cisco MDS 9148S Switch AC Input Power Supply Specifications

AC Input Power Supply

Specification

AC input voltage

Minimum = 90 VAC

Nominal = 100 to 240 VAC

Maximum = 264 VAC

AC input current rating
(maximum)

4.7 A at 85 VAC
3.6 A at 110 VAC
1.8 A at 220 VAC

Note

For plug current rating, see the

“Jumper Power Cord” section on
page 1-6

AC input frequency

Nominal = 50 to 60 Hz

Содержание DS-C9148S48PK9

















































































Результаты поиска

Содержание DS-C9148S48PK9

Отзывы:

Похожие инструкции для DS-C9148S48PK9

Бренды по названию

Популярные бренды

Cisco DS-C9148S48PK9, Руководство по установке оборудования

Результаты поиска

Содержание DS-C9148S48PK9

Отзывы:

Похожие инструкции для DS-C9148S48PK9

Бренды по названию

Популярные бренды