Cisco DS-C9148S48PK9 Скачать руководство пользователя страница 22

Страница: 22 / 80

2-16

Cisco MDS 9148S Multilayer Switch Hardware Installation Guide

OL-20185-01

Chapter 2 Installing the Cisco MDS 9148S Switch

Preinstallation

Note

Each new switch requires a license; see the

Cisco MDS 9000 Family NX-OS Licensing Guide

for

instructions on installing a license.

Preinstallation

This section includes the following information:

•

Installation Options, page 2-16

•

Installation Guidelines, page 2-16

•

Required Equipment, page 2-18

•

Unpacking and Inspecting the Switch, page 2-18

Installation Options

The MDS 9148S Switch can be installed using the following methods:

•

In an open EIA rack, using:

–

The rack-mount kit shipped with the switch

–

The Telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
rack-mount kit shipped with the switch

•

In a perforated or solid-walled EIA cabinet, using:

–

The rack-mount kit shipped with the switch

–

The Telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
rack-mount kit shipped with the switch

•

In a two-post Telco rack, using:

–

The Telco and EIA Shelf Bracket Kit (an optional kit, purchased separately) in addition to the
front brackets shipped with the switch

For instructions on installing the switch using the rack-mount kit shipped with the switch, see the

“Front-Facing Installation” section on page 2-19

For instructions on installing the switch using the optional, separately purchased Telco and EIA Shelf
Bracket Kit, see the

“Cisco MDS 9000 Family Telco and EIA Shelf Bracket” section on page 1-3

Note

The Telco and EIA Shelf Bracket Kit is optional and is not provided with the switch. To order the kit,
contact your switch provider.

Installation Guidelines

Follow these guidelines when installing the Cisco MDS 9148S Switch:

•

Plan your site configuration and prepare the site before installing the switch. The recommended site
planning tasks are listed in

Appendix 1, “Site Planning and Maintenance Records.”

Содержание DS-C9148S48PK9

















































































Результаты поиска

Содержание DS-C9148S48PK9

Отзывы:

Похожие инструкции для DS-C9148S48PK9

Бренды по названию

Популярные бренды

Cisco DS-C9148S48PK9, Руководство по установке оборудования

Результаты поиска

Содержание DS-C9148S48PK9

Отзывы:

Похожие инструкции для DS-C9148S48PK9

Бренды по названию

Популярные бренды