Cisco Catalyst 3650 Скачать руководство пользователя страница 69 | Manualshive

Страница: 69 / 118

background image

3-7

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 3 Power Supply Installation

Installation Guidelines

Installation Guidelines

Table 3-1

lists the switches and the compatible power supply modules. Observe these guidelines when

removing or installing a power supply or fan module:

•

Do not force the power supply or fan module into the slot. This can damage the pins on the switch
if they are not aligned with the module.

•

A power supply that is only partially connected to the switch can disrupt the system operation.

•

Remove power from the power supply module before removing or installing the module.

•

The power supply is hot-swappable. In some configurations, such as full PoE+ or power-sharing
mode, removing a power supply causes powered devices to shut down until the power budget
matches the input power of a single power supply. To minimize network interruption, hot swap the
power supply ensuring that the remaining supply has sufficient PoE power for all powered ports.

For the switch commands that display available power budget, see the software configuration guide.

Note

For information on 250-W AC power supply support on the PoE-capable switch models, refer to the

Release Notes for the Cisco Catalyst 3650 Switch

on Cisco.com.

Caution

Do not operate the switch with one power supply module slot empty. For proper chassis cooling, both
module slots must be populated, with either a power supply or a blank cover.

Table 3-2

Switch Power Supply Module LEDs

AC Power Supply Module LEDs

AC OK

Description

PS OK

Description

Off
(AC LED is
off)

No AC input power.

Off

Output is disabled, or input is
outside operating range.

Green

AC input power present.

Green

Power output to switch.

Red

Output has failed.

DC Power Supply Module LEDs

DC OK

Description

PS OK

Description

Off
(DC LED is
off)

No DC input power.

Off

Output is disabled, or input is
outside operating range.

Green

DC input power present.

Green

Power output to switch.

Red

Output has failed.

«
...
67
68
69
70
71
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: IBM Страницы: 2

RoamAbout RBT-4102-BG

Бренд: Enterasys Страницы: 72

Бренд: F&G Страницы: 6

Бренд: GarrettCom Страницы: 63

QuantaMesh T1048-LB9M

Бренд: QCT Страницы: 34

Бренд: SMART-AVI Страницы: 2

Бренд: UNICOM Страницы: 15

Бренд: FS Страницы: 43

Бренд: Network Technologies Страницы: 7

Бренд: ALFAtron Страницы: 15

TPR22-BM Series

Бренд: KBT Страницы: 4

Бренд: Copal Страницы: 9

Бренд: Southern States Страницы: 32

Бренд: Xtreme Страницы: 15

Бренд: IDK Страницы: 81

Бренд: Cybex Computer Products Страницы: 56

Бренд: Panasonic Страницы: 19

Бренд: Palmer Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды