Cisco Catalyst 3650 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 118

background image

2-4

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 2 Switch Installation

Preparing for Installation

•

When connecting or disconnecting the power cord on a switch that is installed above or below a
1025-W or 1100-W power supply-equipped switch, you might need to remove the module from the
switch to access the power cord.

•

Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent
lighting fixtures. Make sure that the cabling is safely away from other devices that might damage
the cables.

•

For copper connections on Ethernet ports, cable lengths from the switch to connected devices can
be up to 328 feet (100 meters).

•

Each port must match the wave-length specifications on the other end of the cable, and the cable
must not exceed the maximum cable length.

•

Operating environment is within the correct ranges.

•

Airflow around the switch and through the vents is unrestricted.

•

Temperature around the unit does not exceed 113°F (45°C). If the switch is installed in a closed or
multirack assembly, the temperature around it might be greater than normal room temperature.

•

Cisco Ethernet switches are equipped with cooling mechanisms, such as fans and blowers. However,
these fans and blowers can draw dust and other particles, causing contaminant buildup inside the
chassis, which can result in system malfunction. You must install this equipment in an environment
as free from dust and foreign conductive material (such as metal flakes from construction activities)
as is possible.

These standards provide guidelines for acceptable working environments and acceptable levels of
suspended particulate matter:

–

Network Equipment Building Systems (NEBS) GR-63-CORE (only with the DC power supply)

–

National Electrical Manufacturers Association (NEMA) Type 1

–

International Electrotechnical Commission (IEC) IP-20

Tools and Equipment

Obtain these necessary tools and equipment:

•

A number-2 Phillips screwdriver to rack-mount the switch.

•

A Torx T15 screwdriver, or the Torx T15 key that ships with StackWise upgrade kits, to install the
StackWise adapter.

Verifying Switch Operation

Before you install the switch in a rack, or on a table or shelf, you should power on the switch and verify
that the switch passes POST. See the “

Running Express Setup

” section in the getting started guide for

the steps required to connect a PC to the switch and to run Express Setup.

Note

When you connect the RPS to the switch, put the RPS in standby mode. Set the RPS to active mode
during normal operation.

Warning

Attach only the following Cisco external power system to the switch: PWR-RPS2300.

Statement 387

«
...
42
43
44
45
46
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: Quick Страницы: 28

Бренд: Hama Страницы: 10

Бренд: Hama Страницы: 14

Бренд: Comprehensive Страницы: 6

ProSAFE JGS516PE

Бренд: NETGEAR Страницы: 2

Бренд: LEGRAND Страницы: 30

Бренд: ATEN Страницы: 26

Бренд: C4i Страницы: 7

Бренд: A-Neuvideo Страницы: 12

Бренд: Power Ethernet Страницы: 2

Бренд: Lanpro Страницы: 16

Бренд: J-Tech Digital Страницы: 81

Бренд: Eaton Страницы: 3

Бренд: BZB Gear Страницы: 27

Бренд: ALFAtron Страницы: 23

Бренд: Videosec Страницы: 3

Бренд: BCXLAB Страницы: 6

ProSAFE FS526Tv2

Бренд: NETGEAR Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды