Cisco Catalyst 3650 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 118

background image

1-18

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 1 Product Overview

Front Panel

USB Console LED

The USB console LED (

Figure 1-6

) shows whether there is an active USB connection to the port.

ACTV LED

PoE+

1

Off

PoE+ is off.

If the powered device is receiving power from an AC power source,
the port LED is off even if the device is connected to the switch port.

Green

PoE+ is on. The port LED is green when the switch port is providing
power.

Alternating
green and
amber

PoE+ is denied because providing power to the powered device will
exceed the switch power capacity.

Blinking amber PoE+ is off due to a fault or because it has exceeded a limit set in

the switch software.

Caution

PoE+ faults occur when noncompliant cabling or
powered devices are connected to a PoE+ port. Use only
standard-compliant cabling to connect Cisco prestandard
IP Phones and wireless access points or
IEEE 802.3af-compliant devices to PoE+ ports. You must
remove from the network any cable or device that causes
a PoE+ fault.

Amber

PoE+ for the port has been disabled.

Note

PoE+ is enabled by default.

1.

Only switches with PoE or PoE+ ports.

Table 1-4

Meaning of Switch LED Colors in Different Modes (continued)

Port Mode

Port LED Color

Meaning

Table 1-5

USB Console Port LED

Color

Description

Off

USB console is disabled.

Green

USB console is enabled.

Table 1-6

ACTV LED

Color

Description

Off

Switch is not the active switch.

Green

Switch is the active switch or a standalone switch.

«
...
26
27
28
29
30
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: FS Страницы: 23

Бренд: LOVATO ELECTRIC Страницы: 37

Бренд: Erbe Страницы: 118

UltraHD Switch 3:1

Бренд: Oehlbach Страницы: 20

Бренд: Digitronic Страницы: 24

Бренд: Unipoe Страницы: 41

Бренд: Raritan Страницы: 4

SmartSTACK ETHERNET ELS10-27

Бренд: Cabletron Systems Страницы: 126

Instant On 1930 Series

Бренд: Aruba Страницы: 8

Бренд: Scame electrical solutions Страницы: 68

Бренд: DataParts Страницы: 5

Бренд: Edge-Core Страницы: 60

Бренд: steute Страницы: 10

Бренд: TCi Страницы: 11

Бренд: Hubner Страницы: 23

SwitchMan USB-Combo SW4

Бренд: Raritan Страницы: 2

Area box distribution switch

Бренд: LEGRAND Страницы: 87

Бренд: I-Tech Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды