Cisco Catalyst 3650 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 118

background image

2-21

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 2 Switch Installation

Connecting Devices to the Ethernet Ports

PoE inline power supports devices compliant with the IEEE 802.3af standard, as well as prestandard
Cisco IP Phones and Cisco Aironet Access Points. Each port can deliver up to 15.4 W of PoE.

PoE+ inline power supports devices compliant with the IEEE 802.3at standard, by delivering up to 30 W
of PoE+ power per port to all switch ports.

Cisco UPOE™ ports provide up to 60 W power per port for connected devices.

Note

Many legacy powered devices, including older Cisco IP phones and access points that do not fully
support IEEE 802.3af, might not support PoE when connected to the switches by a crossover cable.

Caution

PoE faults are caused when noncompliant cabling or powered devices are connected to a PoE port. Use
only standard-compliant cabling to connect Cisco prestandard IP Phones, wireless access points, or
IEEE 802.3af-compliant devices to PoE ports. A cable or device that causes a PoE fault must be removed
from the network.

Warning

Voice over IP (VoIP) service and the emergency calling service do not function if power fails or is
disrupted. After power is restored, you might have to reset or reconfigure equipment to regain access
to VoIP and the emergency calling service. In the USA, this emergency number is 911. You need to be
aware of the emergency number in your country.

Statement 361

«
...
59
60
61
62
63
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: Campbell Страницы: 14

TotalStorage 3534-F08

Бренд: IBM Страницы: 105

RedBooks SAN24B-5

Бренд: IBM Страницы: 11

RedBooks SAN24B-5

Бренд: IBM Страницы: 2

Бренд: IBM Страницы: 123

8265 Nways ATM Switch

Бренд: IBM Страницы: 192

SynOptics 3000 Series

Бренд: Cabletron Systems Страницы: 101

Crouse-Hinds CEAG KO

Бренд: Cooper Страницы: 12

Бренд: Linksys Страницы: 3

Бренд: Amped Wireless Страницы: 22

Бренд: YA Страницы: 47

Signature ANTENNA GENIUS 8x2 v2 PLUS

Бренд: 4O3A Страницы: 57

Бренд: Davey Страницы: 2

Бренд: DSPPA Страницы: 31

IDS-105FE Series

Бренд: Perle Страницы: 2

Бренд: Black Box Страницы: 44

Бренд: Whelen Engineering Company Страницы: 5

Бренд: Marmitek Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды