Cisco Catalyst 3650 Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 118

background image

7-10

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Appendix 7 Connector and Cable Specifications

Cable and Adapter Specifications

want to connect the switch console port to a terminal. You can order a kit with an adapter (part
number ACS-DSBUASYN=). For console port and adapter pinout information, see

Table 7-2

and

Table 7-3

.

Table 7-2

lists the pinouts for the console port, the RF-45-to-DB-9 adapter cable, and the console device.

Table 7-3

lists the pinouts for the console port, RJ-45-to-DB-25 female DTE adapter, and the

console device.

Note

The RJ-45-to-DB-25 female DTE adapter is not supplied with the switch. You can order a kit with the
adapter (part number ACS-DSBUASYN=) from Cisco.

Table 7-2

Console Port Signaling Using a DB-9 Adapter

Switch Console
Port (DTE)

RJ-45-to-DB-9
Terminal Adapter

Console
Device

Signal

DB-9 Pin

Signal

RTS

8

CTS

DTR

6

DSR

TxD

2

RxD

GND

5

GND

GND

5

GND

RxD

3

TxD

DSR

4

DTR

CTS

7

RTS

Table 7-3

Console Port Signaling Using a DB-25 Adapter

Switch Console
Port (DTE)

RJ-45-to-DB-25
Terminal Adapter

Console
Device

Signal

DB-25 Pin

Signal

RTS

5

CTS

DTR

6

DSR

TxD

3

RxD

GND

7

GND

GND

7

GND

RxD

2

TxD

DSR

20

DTR

CTS

4

RTS

«
...
108
109
110
111
112
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: KELCO Страницы: 41

Бренд: 4O3A Страницы: 2

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

Бренд: Communica Страницы: 5

Бренд: Thinklogical Страницы: 27

Бренд: NeoPro Страницы: 36

Бренд: Enterasys Страницы: 41

Бренд: Hubner Страницы: 23

Бренд: Edimax Страницы: 3

Бренд: steute Страницы: 12

Бренд: SK telecom Страницы: 7

Area box distribution switch

Бренд: LEGRAND Страницы: 87

Бренд: Taiden Страницы: 4

Бренд: Sensor Switch Страницы: 2

JetNet 5428G-20SFP Series

Бренд: Korenix Страницы: 2

Бренд: AV Access Страницы: 16

Бренд: ZIEHL-ABEGG Страницы: 12

Бренд: Manhattan Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды