Cisco Catalyst 3650 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 118

background image

1-23

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 1 Product Overview

Rear Panel

RJ-45 Console Port LED

StackWise Ports

StackWise ports are used to connect switches in StackWise stacking configurations. StackWise cables
are used to connect the StackWise ports for stacking.

A StackWise adapter must be installed in the StackWise port to enable stacking. StackWise adapter
blanks installed in the StackWise ports is the default setup.

For Catalyst 3650 switches where stacking is specified, StackWise adapters are preinstalled in the
StackWise ports, and optional StackWise cables can be ordered. When stacking is not specified, but is
required, the StackWise adapter blanks must be removed and StackWise adapters installed.

Caution

Use only approved cables, and connect only to similar Cisco equipment. Equipment might be damaged
if connected to nonapproved Cisco cables or equipment.

Note

You cannot have a switch stack containing a mix of Catalyst 3650 and Catalyst 3850 switches.

Power Supply Modules

•

Power Supply for Catalyst 3650-24TS/PS/TD/PD and 3650-48TS/PS/FS/TD/PD/FD/FQ/PQ/TQ
Switches, page 1-24

•

Power Supply Module for Catalyst 3650-24PDM and 3650-48FQM Switches, page 1-25

•

Power Supply Module LEDs, page 1-26

The 24- and 48-port switches are powered through one or two internal power supply modules.

The switch has two internal power supply module slots. You can use two AC modules, two DC modules,
a mixed configuration of one AC and one DC power supply module, or one power supply module and a
blank cover. The switch can operate with either one or two active power supply modules.

1

Ground connector

4

Data stack ports

2

CONSOLE (RJ-45 console port)

5

Redundant Power Supply

3

MGMT (RJ-45 10/100/1000 management
port)

6

Power Supply

Table 1-10

RJ-45 Console Port LED

Color

RJ-45 Console Port Status

1

1.

The USB console has priority over the RJ-45 console.

Off

RJ-45 console is disabled. USB console is active.

Green

RJ-45 console is enabled. USB console is disabled.

«
...
31
32
33
34
35
...
»

Содержание Catalyst 3650























































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 3650

Бренд: Techroutes Страницы: 22

Бренд: Ruby Tech Страницы: 2

Бренд: Vega Страницы: 28

Бренд: UfiSpace Страницы: 25

Бренд: Equip Страницы: 10

PC-IA100 Series

Бренд: Barox Страницы: 7

Бренд: ALFAtron Страницы: 68

Бренд: hager Страницы: 2

Бренд: HIKVISION Страницы: 25

Antenna-Disconnect-Switch

Бренд: ADS Страницы: 12

Бренд: Lindy Страницы: 4

MISCOM7220G-4GF-16GT

Бренд: Maiwe Страницы: 6

Бренд: CAMBRIONIX Страницы: 37

Бренд: T.I.P. Страницы: 42

Бренд: Versa Technology Страницы: 96

Бренд: Gefen Страницы: 12

Бренд: HighSecLabs Страницы: 10

Бренд: Link Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды