Cisco Catalyst 3650 Скачать руководство пользователя страница 64

Страница: 64 / 118

3-2

Catalyst 3650 Switch Hardware Installation Guide

OL-29734-01

Chapter 3 Power Supply Installation

Power Supply Module Overview

For information on available PoE, see these sections:

•

(available PoE with AC power supply)

•

(available PoE with DC power supply)

•

(switch power supply requirements for PoE and PoE+, and Cisco UPOE™)

The input voltages of the power supplies are as follows:

•

The 250-W, 640-W and 715-W AC power supply modules are autoranging units that support input
voltages between 100 and 240 VAC.

•

The 1025-W and 1100-W AC power supply modules are autoranging units that supports input
voltages between 115 and 240 VAC.

•

The 440-W and 640-W DC power supply modules have dual input feeds (A and B) and supports
input voltages between 36 and 72 VDC. The output voltage range is 51 to 57 V.

Each AC power supply module has a power cord for connection to an AC power outlet.

•

The 640-W, 715-W, 1025-W and 1100-W and modules use a 16-AWG cord (only North America).
All other modules use an 18-AWG cord.

•

All other modules use an 18-AWG cord

•

The DC power supply module must be wired to a DC power source.

Note

For information on 250-W AC power supply support on the PoE-capable switch models, refer to the

Release Notes for the Cisco Catalyst 3650 Switch

on Cisco.com.

Note

Only the DC power module is NEBS-compliant.

Figure 3-1

Figure 3-7

show the power supply modules.

PWR-C2-640WAC

640-W AC power supply module

PWR-C2-250WAC

250-W AC power supply module

PWR-C2-640WDC

640-W DC power supply module

PWR-C2-BLANK

Blank cover

Table 3-1

Power Supply Module Part Numbers and Descriptions (continued)

Part Number

Description

Содержание Catalyst 3650























































































































Результаты поиска

Содержание Catalyst 3650

Отзывы:

Похожие инструкции для Catalyst 3650

Бренды по названию

Популярные бренды

Cisco Catalyst 3650, Руководство по установке оборудования

Результаты поиска

Содержание Catalyst 3650

Отзывы:

Похожие инструкции для Catalyst 3650

Бренды по названию

Популярные бренды