Cisco ASR 14000 Series Скачать руководство пользователя страница 37

Страница: 37 / 132

2-15

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 2 Installing and Removing Power Components

How to Install or Remove the Power Components

What to Do Next

After performing this task, you may connect the PDU to the power source (see the

“DC Power Systems”

section on page 2-4

and the

“AC Power Systems” section on page 2-8

) and power up the chassis (see the

“Before Powering the Chassis Up or Down” section on page 2-8

Removing a Power Module

This section describes how to remove a power module from the Cisco ASR 14000 series 8-slot line card
chassis. For information on the difference between the power types, see the

“DC Power Systems” section

on page 2-4

and the

“AC Power Systems” section on page 2-8

. For complete information on regulatory

compliance and safety, see

Regulatory Compliance and Safety Information for the Cisco ASR14000

Series Aggregation Services Router

The power module is located on the front of the chassis, and mates with the PDU that is installed on the
back of the chassis (see the

“Installing a PDU” section on page 2-10

for information). Although there

are differences among the power modules (AC Wye, AC Delta, and DC), they are installed in the same
manner. (

Figure 2-9

shows an AC Wye power rectifier for reference.)

Figure 2-9

AC Power Rectifier

Prerequisites

Before performing this task, remove any front cosmetic covers.

Required Tools and Equipment

You need the following tools to perform this task:

•

ESD-preventive wrist strap

•

Medium Phillips screwdriver

Power switch

Handle

Module air filter

Captive screws

POWER

FLT

FAIL

TMP

LLM

122286

Содержание ASR 14000 Series





































































































































Результаты поиска

Содержание ASR 14000 Series

Отзывы:

Похожие инструкции для ASR 14000 Series

Бренды по названию

Популярные бренды

Cisco ASR 14000 Series, Руководство по установке

Результаты поиска

Содержание ASR 14000 Series

Отзывы:

Похожие инструкции для ASR 14000 Series

Бренды по названию

Популярные бренды