Cisco ASR 14000 Series Скачать руководство пользователя страница 72

Страница: 72 / 132

4-20

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 4 Installing and Removing MSCs, PLIMs, and Associated Components

How to Install or Remove a Pillow Block

Prerequisites

Before performing this task, remove any cosmetic covers.

Required Tools and Equipment

You need the following tools to perform this task:

•

ESD-preventive wrist strap

•

Large Phillips screwdriver

Steps

To remove an impedance carrier, follow these steps:

Step 1

Attach the ESD-preventive wrist strap to your wrist and connect its leash to an ESD connection socket
on the rear (MSC) side or a bare metal surface on the chassis.

Step 2

Identify the impedance carrier to be removed from the card cage.

Step 3

To loosen the impedance carrier from the slot, turn the two captive screws on the front panel of the card
counterclockwise.

Step 4

Grasp the impedance carrier handle with one hand and gently pull it halfway from the slot.

Step 5

Place one hand under the impedance carrier to guide it.

Step 6

Holding the impedance carrier underneath and by the handle, pull it from the slot and set it carefully
aside.

What to Do Next

After performing this task, store the impedance carrier for future use. You may now install a card in the
uncovered slot. See the

“Installing an MSC” section on page 4-31

and the

“Installing a PLIM” section

on page 4-47

for further details.

How to Install or Remove a Pillow Block

This section contains the following procedures:

•

Installing a Pillow Block

•

Removing a Pillow Block

Содержание ASR 14000 Series





































































































































Результаты поиска

Содержание ASR 14000 Series

Отзывы:

Похожие инструкции для ASR 14000 Series

Бренды по названию

Популярные бренды

Cisco ASR 14000 Series, Руководство по установке

Результаты поиска

Содержание ASR 14000 Series

Отзывы:

Похожие инструкции для ASR 14000 Series

Бренды по названию

Популярные бренды