Cisco ASR 14000 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 132

background image

1-7

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 1 Overview

Chassis Power System

Note

We recommend that you check the air filters once a month. Replace a filter when you notice a significant
amount of dust.

Figure 1-6

Airflow through 8-the Cisco ASR 14000 Series 8-Slot Line Card Chassis

The Cisco ASR 14000 series 8-slot line card chassis airflow volumes are:

•

Chassis airflow—Up to 900 cubic feet (25,485 liters) per minute

•

Power system airflow—Up to 240 cubic feet (6,800 liters) per minute

Chassis Power System

The Cisco ASR 14000 series 8-slot line card chassis is available with AC power distribution units
(PDUs) that are configured for either AC Wye 3-phase, AC Delta 3-phase, or DC wiring. Each PDU has
a different Cisco part number.

AC Wye and AC Delta PDUs basically both require 220 VAC input power:

•

AC Wye 3-phase wiring is typically used in Europe and countries where each phase-to-neutral
voltage is approximately 220 VAC; the nominal voltage for the power module is 230 V +/- 10%,
which covers the 220 and 240 voltages that are present throughout Europe.

•

AC Delta 3-phase wiring is typically used in the United States, Japan, and other countries where the
phase-to-neutral voltage is approximately 120 VAC and approximately 208 VAC phase to phase.

For DC PDU, there is one type for both nominal -48 VDC and -50 VDC inputs.

Safety Guidelines

Before you perform any procedure in this document, review the safety guidelines in this section to avoid
injuring yourself or damaging the equipment.

250464

Fan

Air enters

PLIM side

Power system

Fan

Air exits fabric
card side

Front

Rear

Air filter

«
...
19
20
21
22
23
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

Бренд: Magnadyne Страницы: 13

DG834GT - 108 Mbps Super G Wireless ADSL Router

Бренд: NETGEAR Страницы: 2

MasterBus Tanklevel Interface

Бренд: Mastervolt Страницы: 8

Бренд: Lanner Страницы: 63

Бренд: Patton electronics Страницы: 2

Бренд: Lanner Страницы: 78

Бренд: ZKTeco Страницы: 68

Бренд: Leviton Страницы: 4

Бренд: Connectland Страницы: 10

AlterPath Manager 2500

Бренд: Cyclades Страницы: 368

Бренд: NetComm Страницы: 75

Бренд: Proscend Страницы: 93

Бренд: Williams Sound Страницы: 2

USB device 622x

Бренд: National Instruments Страницы: 23

Бренд: Comtrend Corporation Страницы: 69

GigaVUE H Series

Бренд: Gigamon Страницы: 55

BIANCA/BRICK XS

Бренд: BinTec Страницы: 2

cnPilot Home R200 Series

Бренд: Cambium Networks Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды