Cisco ASR 14000 Series Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 132

background image

3-7

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 3 Installing and Removing Air Circulation Components

How to Install or Remove Air Circulation Components

Caution

To prevent damage to the chassis connector, do not use excessive force when inserting a fan
tray into its bay.

Step 8

Firmly push on the fan tray to seat the fan tray connector in the chassis connector.

Note

All electrical and control line connections are made automatically when the connectors mate.

Step 9

Rotate the fan tray handle to the closed (flush) position.

Step 10

Replace the fan tray bay door and tighten the two captive screws on the fan tray bay door.

What to Do Next

After performing this task, replace the front cover plates.

Removing an Upper Fan Tray

This section describes how to remove a fan tray from the upper fan tray slot of the Cisco ASR 14000
series 8-slot line card chassis. For information on the chassis airflow and circulation, see the

Card Chassis Airflow” section on page 3-1

. For complete information on regulatory compliance and

safety, see

Regulatory Compliance and Safety Information for the Cisco ASR14000 Series Aggregation

Services Router

.

A Cisco ASR 14000 series 8-slot line card chassis fan tray operates in either the upper or lower fan tray
slot. Each fan tray is installed into the rear (MSC) side of the chassis (see

).

Figure 3-5

Fan Tray

Prerequisites

Before performing this task, you must first open the chassis doors and remove any front cosmetic covers.

1

Captive screws

3

Fan tray handle

2

Fan tray rail

122289

3

2

1

«
...
43
44
45
46
47
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

Verizon DSL-2750B

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 10

Бренд: GE Страницы: 4

Бренд: N-Tron Страницы: 138

Бренд: National Instruments Страницы: 24

Бренд: National Instruments Страницы: 32

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 8

VigorIPPBX 2820 Series

Бренд: Draytek Страницы: 29

Бренд: REXROTH Страницы: 68

Бренд: Vonets Страницы: 8

Net2Air Ins-40085-US

Бренд: Paxton Страницы: 4

Бренд: ZyXEL Communications Страницы: 215

Speedway Revolution

Бренд: impinj Страницы: 60

Бренд: ACTi Страницы: 12

Бренд: Talent Страницы: 18

Бренд: ACTi Страницы: 14

Acme Packet 3900

Бренд: Oracle Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды