Cisco ASR 14000 Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 132

background image

3-12

Cisco ASR 14000 Series Router 8-Slot Line Card Chassis Installation Guide

OL-16973-01

Chapter 3 Installing and Removing Air Circulation Components

How to Install or Remove Air Circulation Components

Required Tools and Equipment

You need the following tools and part to perform this task:

•

ESD-preventive wrist strap

•

Medium flat-blade screwdriver

•

Air filter (Cisco product number ASR14K-8-PWR-FILTER=)

Steps

To install a power module air filter, follow these steps:

Step 1

Attach the ESD-preventive wrist strap to your wrist and connect its leash to one of the ESD connection
sockets on the front (PLIM) side of the chassis or a bare metal surface on the chassis.

Step 2

Place the screwdriver under the edge of the air filter clip-on holder.

Step 3

Gently pry the holder loose with the screwdriver; it should pop off easily.

Step 4

Place the air filter in position on the front of the power module.

Step 5

Place the holder in position on the front of the power module over the air filter.

Step 6

Press the holder firmly but gently until it snaps into place.

What to Do Next

After performing this task, replace the front cover plates.

Removing a Power Module Air Filter

This section describes how to remove a power module air filter. For further information, see the

Line Card Chassis Airflow” section on page 3-1

. For complete information on regulatory compliance

and safety, see

Regulatory Compliance and Safety Information for the Cisco ASR14000 Series

Aggregation Services Router

.

Each power module has a serviceable air filter that is attached to the front of the power module and is
held in place by an air filter clip-on holder. The power module air filter faces outward from the front of
the chassis (see

«
...
48
49
50
51
52
...
»

Содержание ASR 14000 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 14000 Series

Бренд: 3Com Страницы: 20

UR5i v2 Libratum

Бренд: B+B SmartWorx Страницы: 8

Бренд: B+B SmartWorx Страницы: 8

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

5big - Network NAS Server

Бренд: LaCie Страницы: 9

Бренд: LaCie Страницы: 14

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

ADSL 2/2+ Router with USB Port ADE-3410v2

Бренд: Planet Страницы: 62

Бренд: ADTRAN Страницы: 9

Бренд: ForeScout Страницы: 28

Бренд: Patton Страницы: 62

Бренд: ADTRAN Страницы: 20

Бренд: MA lighting Страницы: 49

Бренд: Dataprobe Страницы: 16

Бренд: Paradyne Страницы: 6

Бренд: TRENDnet Страницы: 57

Бренд: Tripp Lite Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды