Cisco Aironet 1040 Series Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 276

background image

Cisco 1522

Cisco 1552 E/H

Cisco 1552 I/C

Parameter

8 dBi

7 dBI

4 dBi (inbuilt antenna)

Tx Antenna Gain

0 dB

4 dB

4 dB

Tx Beam Forming (BF)

35.5 dBm

36.5 dBm

36 dBm

Tx EIRP

8 dBi

7 dBI

4 dBi

Rx Antenna Gain

0.5 dB

0.5 dB

0 dB

Rx Antenna Cable Loss

–88 dBm at 9 Mbps

–91 dBm at 9 Mbps

–91 dBm at 9 Mbps

Rx Sensitivity

131 dB

134 dB

131 dB

System Gain

9 dB

9 dB

9 dB

Fade Margin

829 meters (2722 feet)

1120 meters (3675 feet)

829 meters (2722 feet)

Range between APs
(LOS, PLE = 2.3)

The AP1552 models with built-in antennas (1552C/I) have the same system gain as AP1522s for 5-GHz
backhaul giving the AP to AP distance of 2722 feet. A fade margin of 9 dB is assumed, which is inconsistent
with the assumption to calculate the required SNR values in the

Wireless Mesh Constraints

section.

Link Budget Analysis for AP to Client (–A Domain)

This section contains a link budget analysis for the AP to the Client, so that you know how far away a client
can go from the AP with a system gain value in each band. In this analysis, the focus is on the system gain
for upstream and downstream. A link should be balanced for upstream and downstream, but it might not
happen. Generally, there is a higher antenna gain and higher Tx power available on the AP rather than on the
client. But, this can also be opposite in a few regulatory domains because of different EIRP limit requirements.
Therefore, the lowest of both upstream and downstream should be taken to calculate the AP to the client
distance because that will be the decision factor. For example, if there is a higher downstream gain than
upstream, the upstream should be the decision maker for the cell size because the upstream system gain allows
only the client to connect to the AP.

The regulatory domain values of Tx EIRP and Rx sensitivities decide whether upstream or downstream has
the lower system gain. The cell size should be determined by upstream and not downstream.

Because most of the clients available are 2.4-GHz clients, the focus is on the 2.4-GHz AP to the.

For the AP to client link budget in 2.4 GHz, let us assume a client Tx power of 20 dB and an antenna gain of
0 dBi (see

Table 22: Outdoor 11n AP-to-Client, at 2.4 GHz: 9 Mbps Data Rate (–A domain), on page 78

).

For the –A domain EIRP limit is 36 dBm for 2.4- and 5-GHz bands.

.

Cisco Mesh Access Points, Design and Deployment Guide, Release 7.3

OL-27593-01

77

Site Preparation and Planning

Cell Planning and Distance

«
...
91
92
93
94
95
...
»

Содержание Aironet 1040 Series





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Aironet 1040 Series

Бренд: Hal Communications Страницы: 25

Бренд: Paradyne Страницы: 16

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

LS42 - BladeCenter - 7902

Бренд: IBM Страницы: 56

Бренд: IBM Страницы: 2

BladeCenter Management Module

Бренд: IBM Страницы: 78

Бренд: IBM Страницы: 110

Remote Supervisor Adapter II

Бренд: IBM Страницы: 132

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: Ebyte Страницы: 14

Бренд: NETGEAR Страницы: 2

Бренд: TP-Link Страницы: 73

Бренд: NEC Страницы: 2

Hollywood DV-Bridge

Бренд: Dazzle Страницы: 63

Бренд: Idis Страницы: 31

Бренд: Toto Link Страницы: 55

Бренд: Hama Страницы: 6

Aquaduct 360 XT

Бренд: Aqua Computer Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды