Cisco 2431 - IAD Router Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 124

background image

3-26

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 3 Configuring with the Command-Line Interface

Configuring a VIC2-2FXS or VIC2-4FXS Voice Interface Card

Configuring a VIC2-2FXS or VIC2-4FXS Voice Interface Card

In most situations, the default voice-port values are adequate for FXS voice ports.

Note

The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards.

If you need to change the default configuration for the FXS voice ports, perform the following tasks.
The first two tasks are required; the third task is optional.

Step 1

Identify the voice port and enter voice-port configuration mode.

Step 2

Configure the following mandatory voice-port parameters:

a.

Connection

b.

Dial type

Step 6

signal {groundstart|loopstart|live-feed}

Example:

Router(config-voice-port)# signal groundstart

Configures the signaling type for analog FXO voice
ports. The default is loop-start.

Step 7

compand-type {u-law|a-law}

Example:

Router(config-voice-port)# compand-type a-law

Configures the companding standard used to convert
between analog and digital signals in PCM systems.

Step 8

cptone

local

Example:

Router(config-voice-port)# cptone ca

Configures the appropriate call progress tone for the
local region.

The default for this command is

northamerica

. For a list

of supported countries, see the

Cisco

Voice, Video, and

Fax Command Reference, Release 12.3(4)T

.

Step 9

description

string

Example:

Router(config-voice-port)#

description purchasing_dept

(Optional) Enters a string description for the voice port.
The string describes the voice port in displays. You can
use the description command to note the voice port
location or use.

Step 10

exit

Example:

Router(config-voice-port)# exit

Exits to voice-port mode.

Step 11

Ctrl-z

Example:

Router#

Returns to enable mode when you finish configuring the
interfaces.

Command or Action

Purpose

«
...
58
59
60
61
62
...
»

Содержание 2431 - IAD Router





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2431 - IAD Router

Ray 3 Plus Client

Бренд: Sun Microsystems Страницы: 6

Бренд: Moxa Technologies Страницы: 19

Бренд: Fortinet Страницы: 20

Avenue Express Control Panel

Бренд: Ensemble Designs Страницы: 19

Storagelibrary T24

Бренд: Tandberg Data Страницы: 28

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Бренд: peplink Страницы: 2

Бренд: Garland Страницы: 43

Бренд: Renesas Страницы: 2

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

IPS Pro-Module-24C-GE-BP-TM

Бренд: Trend Micro Страницы: 3

IP-Logic ZIG-IPPRO-RX

Бренд: Zigen Страницы: 4

Бренд: ZyXEL Communications Страницы: 23

Бренд: Black Box Страницы: 12

Бренд: Commell Страницы: 17

Бренд: artisan Страницы: 36

ST7-EMU3 Series

Бренд: ST Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды