Cisco 2431 - IAD Router Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 124

background image

3-7

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 3 Configuring with the Command-Line Interface

Configuring T1/E1 Interfaces

Configuring T1/E1 Interfaces

To configure an ISDN PRI, channel-associated signaling (CAS) interface, or a T1/E1 multiflex trunk
interface, use the configuration software provided with your Cisco IAD or network module (if any).
Otherwise, for greatest power and flexibility, use configuration mode (manual configuration). In this
mode, you enter Cisco IOS commands at the prompt.

This section covers the following topics:

•

Configuring Channel Groups on T1/E1 to Support Data

•

Configuring Channel Groups on T1/E1 to Support Data Under SHDSL Controller

•

Configuring Digital Voice on T1/E1

•

Configuring TDM Cross-Connect

Note

Before you begin, disconnect all WAN cables from the Cisco IAD to prevent it from running the
AutoInstall process. Whenever you power on the Cisco IAD, if there is a WAN connection on both ends
and the Cisco IAD does not have a valid configuration file stored in NVRAM (for instance, when you
add a new interface), the Cisco IAD tries to run AutoInstall. It can take several minutes for the Cisco
IAD to determine that AutoInstall is not connected to a remote TCP/IP host.

This section describes basic configuration, including enabling the interface and specifying IP routing.
Depending on your own requirements and the protocols that you plan to route, you might need to enter
additional configuration commands.

Before you begin configuring the interfaces, make sure to do the following:

•

Connect a console to the Cisco IAD.

•

Power on the Cisco IAD.

Step 6

network-clock-select

priority

{bri|atm|t1|e1}

slot/port

Example:

Router(config)# network-clock-select 1 T1 1/0

Selects the controller as a candidate for the clock
selection algorithm according to the priority entered. Use
either slots 1/0 or 0/0.

Step 7

network-clock-select

priority

serial

slot/port

Example:

Router(config)# network-clock-select 1 Serial 0/0

In case of a serial interface, selects the serial controller
as a candidate for the clock selection algorithm
according to the priority entered. This applies only when
the serial interface is used for time-division multiplexing
(TDM) connections.

Step 8

exit

Example:

Router(config-if)# exit

Exits to global configuration mode.

Step 9

Ctrl-z

Example:

Router#

Returns to enable mode when you finish configuring
interfaces.

Command or Action

Purpose

«
...
39
40
41
42
43
...
»

Содержание 2431 - IAD Router





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2431 - IAD Router

Express Ethernetwork DI-704P

Бренд: D-Link Страницы: 17

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Wireless Router

Бренд: Watchguard Страницы: 11

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 155

Бренд: Omnia Страницы: 102

Бренд: GE Страницы: 93

Бренд: YASKAWA Страницы: 34

SmartMedia Adapter PC Card REX-SMA01F

Бренд: Ratoc Systems Страницы: 75

Бренд: Salus Страницы: 16

ThunderLAN TNETE100A

Бренд: Texas Instruments Страницы: 179

Бренд: LogLogic Страницы: 30

Бренд: Mercusys Страницы: 35

Compact Emulator M30620T-CPE

Бренд: Renesas Страницы: 52

Бренд: Teac Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды