Cisco 2431 - IAD Router Скачать руководство пользователя страница 28

Страница: 28 / 124

2-8

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 2 Using the setup Command Facility

Configuring Controller and Interface Parameters

Sample configurations for the following encapsulation types are provided in this section:

•

Frame Relay Encapsulation

•

LAPB Encapsulation

•

X.25 Encapsulation

•

SMDS Encapsulation

Frame Relay Encapsulation

The following is an example of a typical Frame Relay encapsulation configuration:

The following lmi-types are available to be set,

when connected to a frame relay switch

[0] none

[1] ansi

[2] cisco

[3] q933a

Enter lmi-type [2]:

Note

The setup command facility prompts for the data-link connection identifier (DLCI) number only if you
specify

none

for the Local Management Interface (LMI) type. If you accept the default or specify

another LMI type, the DLCI number is provided by the specified protocol.

Enter the DLCI number for this interface [16]:

Do you want to map a remote machine’s IP address to dlci? [yes]:

IP address for the remote interface: 2.0.0.2

Do you want to map a remote machine’s IPX address to dlci? [yes]:

IPX address for the remote interface: 40.1234.5678

Serial interface needs clock rate to be set in dce mode.

The following clock rates are supported on the serial interface.

1200, 2400, 4800, 9600, 19200, 38400

56000, 64000, 72000, 125000, 148000, 500000

800000, 1000000, 1300000, 2000000, 4000000, 8000000

choose speed from above: [2000000]: 1200

Configure IP on this interface? [yes]:

IP address for this interface: 2.0.0.1

Subnet mask for this interface [255.0.0.0]:

Class A network is 2.0.0.0, 8 subnet bits; mask is /8

LAPB Encapsulation

The following is an example of a typical LAPB configuration:

lapb circuit can be either in dce/dte mode.

Choose either from (dce/dte) [dte]:

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды