Cisco 2431 - IAD Router Скачать руководство пользователя страница 32

Страница: 32 / 124

2-12

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 2 Using the setup Command Facility

Configuring Controller and Interface Parameters

Switched Mode

The following is an example of a 1-port, 4-wire 56-kbps DSU/CSU switched-mode configuration using
the setup command facility:

Do you want to configure Serial0/0 interface? [yes]:

Some encapsulations supported are

ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25

Choose encapsulation type [ppp]:

Switched 56k interface may either be in switched/Dedicated mode

Choose from either (switched/dedicated) [switched]:

The following switched carrier types are to be set when in switched mode

(at&t, sprint or other)

Choose carrier (at&t/sprint/other) [other]:

Do you want to map the remote machine's ip address in dialer map? [yes]:

IP address for the remote interface : 1.0.0.2

Note

The setup command facility asks for only one telephone number for both IP and IPX (if IPX is enabled).

Please enter the phone number to call : 1234567890

Configure IP on this interface? [yes]:

IP address for this interface: 1.0.0.1

Subnet mask for this interface [255.0.0.0] :

Class A network is 1.0.0.0, 8 subnet bits; mask is /8

Dedicated Mode

The following is an example of a 1-port, 4-wire 56-kbps DSU/CSU dedicated-mode configuration using
the setup command facility:

Do you want to configure Serial0/0 interface? [yes]:

Some encapsulations supported are

ppp/hdlc/frame-relay/lapb/atm-dxi/smds/x25

Choose encapsulation type [ppp]:

Switched 56k interface may either be in switched/Dedicated mode

Choose from either (switched/dedicated) [switched]: dedi

When in dds mode, the clock for sw56 module can either from line/internal.

Choose clock from (line/internal) [line]:

Note

internal

is selected, speed cannot be set to “auto.” Autosensing is allowed only when the clock source

line

When in dds mode, the clock for sw56 module can either be from line/internal.

Choose clock from (line/internal) [line]: internal

Warning: internal can be choose only when connected back to back.

Serial interface needs clock rate to be set in dce mode.

The following clock rates are supported on the serial interface.

auto, 2.4, 4.8, 9.6, 19.2, 38.4

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды