Cisco 2431 - IAD Router Скачать руководство пользователя страница 100

Страница: 100 / 124

B-4

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Appendix B Formatting the Flash Memory

Formatting Procedures for Flash Memory

•

Remove the files from flash memory previously formatted with a Class B flash file system

For external flash memory, enter the

erase slot0:

command.

Note

slot0

is not supported on the IAD2435 IAD.

Note

The IAD2435 IAD supports the class C file system.

For internal flash memory, enter the

erase flash:

command.

The following example shows sample output for formatting an external flash memory with a Class B
flash file system:

Router#

erase slot0:

Erasing the slot0 filesystem will remove all files! Continue? [confirm]

Current DOS File System flash card in slot0: will be formatted into Low

End File System flash card! Continue? [confirm]

Erasing device...

eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

...erased

Erase of slot0: complete

Formatting Flash Memory as a Class C File System

Use these formatting commands to do the following:

•

Format flash memory with a Class C flash file system

•

Remove the files from flash memory previously formatted with a Class C flash file system

Note

The IAD2435 IAD supports the class C file system.

For external flash memory, enter the

format slot0:

command.

Note

slot0

is not supported on the IAD2435 IAD.

For internal flash memory, enter the

format flash:

command.

Note

The IAD2435 IAD does not support LEFS, but supports Disk Operating System Filing System (DOSFS)
and refers to internal compact flash as flash only.

The following example shows sample output for formatting an internal flash memory with a Class C
flash file system:

Router#

format flash:

Format operation may take a while. Continue? [confirm]

Format operation will destroy all data in "flash:". Continue? [confirm]

Enter volume ID (up to 64 chars)[default flash]:

Current Low End File System flash card in flash will be formatted into DOS

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды