Cisco 2431 - IAD Router Скачать руководство пользователя страница 23

Страница: 23 / 124

2-3

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 2 Using the setup Command Facility

Configuring Global Parameters

Upgrade ROMMON initialized

program load complete, entry point: 0x80020000, size: 0x18d54b8

Self decompressing the image :

##########################################################################################

################################# [OK]

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

Rights clause at FAR sec. 52.227-19 and subparagraph

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, C2435 Software (C2435-ADVIPSERVICESK9-M), Version

12.4(IAD_APRIL18_POST_SYNC_BUILD.2008-04-17) UBUILDIT Image, CISCO DEVELOPMENT TEST

VERSION

Compiled Fri 18-Apr-08 01:58 by gopasaha

This product contains cryptographic features and is subject to United

States and local country laws governing import, export, transfer and

use. Delivery of Cisco cryptographic products does not imply

third-party authority to import, export, distribute or use encryption.

Importers, exporters, distributors and users are responsible for

compliance with U.S. and local country laws. By using this product you

agree to comply with applicable laws and regulations. If you are unable

to comply with U.S. and local laws, return this product immediately.

A summary of U.S. laws governing Cisco cryptographic products may be found at:

http://www.cisco.com/wwl/export/crypto/tool/stqrg.html

If you require further assistance please contact us by sending email to

[email protected].

Cisco IAD2435 (MPC8323E) processor (revision 0x100) with 249856K/12288K bytes of memory.

Processor board ID FOC11375MBF

MPC8300 CPU Rev: Part Number 0x8062, Revision ID 0x11

2 FastEthernet interfaces

8 Voice FXS interfaces

256K bytes of non-volatile configuration memory.

126000K bytes of ATA Flash (Read/Write)

--- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: y

At any point you may enter a question mark '?' for help.

Use ctrl-c to abort configuration dialog at any prompt.

Default settings are in square brackets '[]'.

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды