Cisco 2431 - IAD Router Скачать руководство пользователя страница 33

Страница: 33 / 124

2-13

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 2 Using the setup Command Facility

Completing the Configuration

56, 64

choose clock rate from above [56]:

Configure IP on this interface? [yes]:

IP address for this interface: 1.0.0.1

Subnet mask for this interface [255.0.0.0] :

Class A network is 1.0.0.0, 8 subnet bits; mask is /8

Completing the Configuration

When you have all the information that the setup command facility has prompted you for, the
configuration appears.

Note

For sample configurations, see

Appendix A, “Cisco IAD2430 Series Configuration Examples.”

To complete your configuration, follow these steps:

Step 1

A setup command facility prompt asks if you want to save this configuration, with the following options:

[0] Go to the IOS command prompt without saving this config.

[1] Return back to the setup without saving this config.

[2] Save this configuration to nvram and exit.

If you answer

, the configuration information you entered is

not

saved, and you return to the Cisco IAD

enable prompt (

Router#

). Enter

setup

to return to the System Configuration Dialog.

If you answer

, you return to setup without saving the configuration.

If you answer

, the configuration is saved and you are returned to the user EXEC prompt

(Router>)

Step 2

When the messages stop appearing on your screen, press

Enter

to get the

Router>

prompt.

Step 3

The

Router>

prompt indicates that you are now at the command-line interface (CLI) and you have just

completed a basic Cisco IAD configuration. However, this is

not

a complete configuration. At this point

you have two choices:

•

Run the setup command facility again and create another configuration. Enter the following:

Router>

enable

Password:

password

Router#

setup

•

Modify the existing configuration or configure additional features with the CLI as described in

Chapter 3, “Configuring with the Command-Line Interface.”

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды