Cisco 2431 - IAD Router Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 124

background image

C H A P T E R

3-1

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

3

Configuring with the Command-Line Interface

This chapter describes how to use the Cisco IOS software command-line interface (CLI) to configure
basic Cisco integrated access device (IAD) functionality.

This chapter presents the following major topics:

•

Configuring the Hostname and Password, page 3-2

•

Configuring Fast Ethernet Interfaces, page 3-4

•

Configuring Network Clock, page 3-5

•

Configuring T1/E1 Interfaces, page 3-7

•

Configuring a WIC-1DSU-T1/E1 Serial WAN Interface Card, page 3-20

•

Configuring a WIC-1T or WIC-2T Serial WAN Interface Card, page 3-24

•

Configuring a VIC2-2FXO or VIC2-4FXO Voice Interface Card, page 3-24

•

Configuring a VIC2-2FXS or VIC2-4FXS Voice Interface Card, page 3-26

•

Configuring ATM T1-WAN Ports, page 3-28

•

Configuring 1-Port ADSL/SHDSL WAN Interface Card, page 3-32

•

Configuring a VIC2-2BRI-NT/TE Card, page 3-36

•

Saving Configuration Changes, page 3-38

Follow the procedures in this chapter to configure the Cisco IAD manually or, if you wish, to change the
configuration after you have run the setup command facility (see the

“The setup Command Facility”

section on page 2-2

).

This chapter does not describe every configuration possible—only a small portion of the most commonly
used configuration procedures. For advanced configuration topics, see the Cisco IOS configuration
guide and command reference publications. See the

“Obtaining Documentation and Submitting a

Service Request” section on page -ix

.

Note

If you skipped

Chapter 2, “Using the setup Command Facility,”

and you have never configured a

Cisco IAD, return to

Chapter 2, “Using the setup Command Facility,”

and read it now. The chapter

contains important information that you need for configuring your Cisco IAD.

Note

The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards.

«
...
33
34
35
36
37
...
»

Содержание 2431 - IAD Router





























































































































Отзывы:

Нет отзывов

Похожие инструкции для 2431 - IAD Router

Бренд: GE Страницы: 4

Бренд: DAQ system Страницы: 41

Бренд: DAQ system Страницы: 19

Бренд: IDT Страницы: 281

DMX-Universal-Demux

Бренд: DMX4ALL Страницы: 17

Бренд: Rockwell Automation Страницы: 108

Бренд: Qixiang Technology Страницы: 16

Бренд: Hama Страницы: 6

Бренд: A4Tech Страницы: 8

JetStor NAS 724UX

Бренд: AC&NC Страницы: 117

Бренд: NETGEAR Страницы: 142

EdgeRouter PoE ERPoe-5

Бренд: Ubiquiti Страницы: 13

ADSL Ethernet & USB Combo Router Lynx L-510

Бренд: Starbridge Networks Страницы: 59

Бренд: Edimax Страницы: 15

Бренд: ADTRAN Страницы: 4

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: Mobily Страницы: 12

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды