Cisco 2431 - IAD Router Скачать руководство пользователя страница 45

Страница: 45 / 124

3-11

Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide

OL-4306-03

Chapter 3 Configuring with the Command-Line Interface

Configuring T1/E1 Interfaces

Configuring Digital Voice on T1/E1

Digital voice is supported by both ISDN and PRI signaling. This section covers the following topics:

•

Configuring Switch Types for ISDN PRI Q.931 Support

•

Configuring DS0 Groups for CAS

For more information on configuring ISDN voice interfaces, see the

Basic ISDN Voice-Interface

Configuration

document.

Step 5

mode {atm|t1|e1}

Example:

Router(config-controller)# mode t1

Specifies that the full T1/E1 line is used as the channel
group mode.

Step 6

controller t1

slot/port

Example:

Router(config)# controller t1 0/2

Specifies the T1 interface for control.

Step 7

channel-group

channel-group-number

timeslots

range

Example:

Router(config-controller)# channel-group 1

timeslots 1-24

Specifies the channel group and time slots to be mapped.

Step 8

interface

type number

Example:

Router(config-controller)#

interface serial 1/0:0

Configures each channel group as a virtual serial
interface. Specifies the T1/E1 interface, unit number, and
channel group to modify.

Step 9

ip address

ip address subnet mask

Example:

Router(config-if)# ip address 10.1.15.1

255.255.255.0

Assigns an IP address and subnet mask to the interface.

Step 10

exit

Example:

Router(config-if)# exit

Exits to global configuration mode.

Step 11

Ctrl-z

Example:

Router#

Returns to enable mode when you finish configuring
interfaces.

Command or Action

Purpose

Содержание 2431 - IAD Router





























































































































Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды

Cisco 2431 - IAD Router, Руководство по настройке программного обеспечения

Результаты поиска

Содержание 2431 - IAD Router

Отзывы:

Похожие инструкции для 2431 - IAD Router

Бренды по названию

Популярные бренды