GASKET DISASSEMBLY
Parts assembled with form-in-place gaskets may be
disassembled
without
unusual
effort.
In
some
instances, it may be necessary to lightly tap the part
with a mallet or other suitable tool to break the seal
between the mating surfaces. A flat gasket scraper
may also be lightly tapped into the joint but care
must be taken not to damage the mating surfaces.
SURFACE PREPARATION
Scrape clean or wire brush all gasket surfaces to
remove all loose material. Inspect stamped parts to
ensure gasket rails are flat. Flatten rails with a ham-
mer on a flat plate if required. Gasket surfaces must
be free of oil and dirt. Make sure old gasket material
is removed from blind attaching holes.
FORM-IN-PLACE GASKET APPLICATION
Assembling parts using a form-in-place gasket
requires care but it’s easier then using precut gas-
kets.
Mopar Gasket Maker material should be applied
sparingly 1 mm (0.040 in.) diameter or less of sealant
to one gasket surface. Be certain the material sur-
rounds each mounting hole. Excess material can eas-
ily be wiped off. Components should be torqued in
place within 15 minutes. The use of a locating dowel
is recommended during assembly to prevent smear-
ing the material off location.
The Mopar Silicone Rubber Adhesive Sealant gas-
ket material or equivalent should be applied in a con-
tinuous bead approximately 3 mm (0.120 in.) in
diameter. All mounting holes must be circled. For
corner sealing, a 3.17 or 6.35 mm (1/8 or 1/4 in.) drop
is placed in the center of the gasket contact area.
Uncured sealant may be removed with a shop towels.
Components should be torqued in place while the
sealant is still wet to the touch (within 10 minutes).
The usage of a locating dowel is recommended during
assembly to prevent smearing of material off loca-
tion.
ENGINE CORE PLUGS
REMOVAL
Using a blunt tool such as a drift or a screwdriver
and a hammer, strike the bottom edge of the cup
plug (Fig. 1). With the cup plug rotated, grasp firmly
with pliers or other suitable tool and remove plug
(Fig. 1).
CAUTION:
Do not drive cup plug into the casting
as restricted cooling can result and cause serious
engine problems.
INSTALLATION
Thoroughly remove all rust and clean inside of cup
plug hole in cylinder block or head. Be sure to
remove old sealer. Lightly coat inside of cup plug hole
with sealer. Make certain the new plug is cleaned of
all oil or grease. Using proper drive plug, drive plug
into hole so that the sharp edge of the plug is at
least 0.5 mm (0.020 inch.) inside the lead in chamfer
(Fig. 1).
It is in not necessary to wait for curing of the seal-
ant. The cooling system can be refilled and the vehi-
cle placed in service immediately.
ENGINE PERFORMANCE
If a loss of performance is noticed, ignition timing
should be checked. timing belt or chain may have
skipped one or two teeth. Camshaft and crankshaft
timing should also be checked. Refer to Group 9,
Engine Timing belt or chain installation.
To provide best vehicle performance and lowest
vehicle emissions, it is most important that the
tune-up be done accurately. Use the specifications
listed on the Vehicle Emission Control Information
label found in the engine compartment.
(1)
Test cranking amperage draw. See Starting
Motor Cranking Amperage Draw Electrical Section of
this manual.
(2) Check intake manifold for vacuum leaks.
PERFORM CYLINDER COMPRESSION TEST
(1) Check engine oil level and add oil if necessary.
(2)
Drive the vehicle until engine reaches normal
operating temperature. Select a route free from traf-
fic and other forms of congestion, observe all traffic
laws, and accelerate through the gears several times
briskly.
(3)
Remove all spark plugs from engine. As spark
plugs are being removed, check electrodes for abnor-
Fig. 1 Core Hole Plug Removal
CYLINDER
BLOCK
SECOND REMOVE PLUG
WITH PLIERS
FIRST STRIKE HERE
WITH HAMMER
DRIFT
CUP PLUG
9 - 2
ENGINE
JA
GENERAL INFORMATION (Continued)
Содержание Stratus LHD 1997
