Christie Roadie 4K35 Скачать руководство пользователя страница 34

Страница: 34 / 87

Inaccurate display colors

The colors of the projected image are not displaying accurately.

Resolution

•

Adjust the color, tint, color space, and color temperature settings of the input source.

•

On the touch panel controller, tapMenu > Configuration > Color Correction and verify the
settings are correct.

Display is not rectangular

The image displayed on the screen is not rectangular.

Resolution

•

Verify the projector is level and the lens surface and screen are parallel to one another.

•

Adjust the vertical offset of the lens mount.

Display has suddenly frozen

The image on the screen has frozen.

Resolution

•

If the source is frozen, restart the source device.

•

If the source is not frozen, restart the projector.

Display is jittery or unstable

The projected image has become jittery or unstable.

Resolution

•

Verify that the input device is connected properly. If the input device is not connected properly,
the projector repeatedly attempts to display an image.

•

The horizontal or vertical scan frequency of the input signal may be out of range for the
projector.

Troubleshooting

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Содержание Roadie 4K35
























































































Результаты поиска

Содержание Roadie 4K35

Отзывы:

Похожие инструкции для Roadie 4K35

Бренды по названию

Популярные бренды

Christie Roadie 4K35, Руководство по обслуживанию

Результаты поиска

Содержание Roadie 4K35

Отзывы:

Похожие инструкции для Roadie 4K35

Бренды по названию

Популярные бренды