Christie Roadie 4K35 Скачать руководство пользователя страница 33

Страница: 33 / 87

1. On the touch panel controller, tap Menu > Lamp LampLOC and adjust the lamp

position manually.

2. Observe screen brightness by adjusting the X, Y and Z values or use a light meter to

check for changes in brightness.

•

Make sure that the anode yoke is in the correct location.

•

Check that the flat part of the anode end of the lamp (if applicable) faces up in the anode
yoke.

Touch panel controller is blank

The projector is powered on but the touch panel controller (TPC) is blank.

Details

The touch panel controller is a touch-sensitive screen used to control the projector, manage sources,
adjust the display, and view status information.

Resolution

•

If the touch panel controller display is blank, make sure the touch panel controller
communication harness is connected securely.

Blank screen, no display of image

The projector is powered on but the screen is blank and no image is displayed.

Resolution

•

Make sure both lens caps have been removed from the projection lens.

•

Make sure the lamp is on.

•

Make sure that all power connections are good.

•

Make sure the shutter is fully open.

•

Make sure that any test pattern (other than a full black test pattern or test pattern = none)
displays properly.

Cannot communicate with the projector

The remote computer or server cannot establish communication with the projector.

Resolution

•

Make sure the computer and the projector are both connected to the network.

•

Make sure that all input devices have the same subnet mask and unique IP addresses.

Troubleshooting

Roadie 4K35 and 4K45 Service Manual

020-101694-03 Rev. 1 (01-2016)

Содержание Roadie 4K35
























































































Результаты поиска

Содержание Roadie 4K35

Отзывы:

Похожие инструкции для Roadie 4K35

Бренды по названию

Популярные бренды

Christie Roadie 4K35, Руководство по обслуживанию

Результаты поиска

Содержание Roadie 4K35

Отзывы:

Похожие инструкции для Roadie 4K35

Бренды по названию

Популярные бренды