Christie Roadie 4K35 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 87

background image

Inspecting the rear exhaust assembly

The rear exhaust assembly includes an exhaust grille between the plastic louvers.
Check: Monthly or sooner when operating the projector in a dusty or dirty environment

1. Remove four screws from the rear exhaust cover to access the exhaust grill.
2. Replace the mesh screen if it appears clogged or blocked with dust or dirt.

Filtration

Filters help to keep dust and other foreign materials out of the projector.

Notice. Failure to comply with the following may result in property damage.

•

Do not operate the product without the filter installed.

•

Use only high efficiency Christie approved filters.

•

Do not reuse an old air filter.

Inspecting the light engine air filter

The light engine filter is located on the lens side of the projector behind the air filter cover.
Check: Monthly

Remove and clean the light engine air filter (on page 45) when replacing the lamp or sooner
when operating the projector in a dusty or dirty environment.

Inspecting the laminar airflow device filter

The laminar airflow device (LAD) filter is attached to the light engine assembly handle in the light

engine compartment.
Check: Every 6 months

Replace the LAD filter.

Inspecting and cleaning lamps

Inspect and clean the lamps to ensure optimum brightness.
Every 60 days

Danger! Failure to comply with the following results in death or serious injury.

•

This procedure must be performed by Christie qualified technicians.

•

SHOCK HAZARD! Disconnect the product from AC before moving, servicing, cleaning, removing
components, or opening any enclosure.

•

EXPLOSION HAZARD! Always wear manufacturer approved protective safety clothing (gloves,
jacket, face shield) whenever the lamp door is open or when handling the lamp. Any local or
federal specifications take precedence over Christie's protective clothing recommendations.

•

EXPLOSION HAZARD! Allow sufficient time for the lamp to cool down before powering down the
product, disconnecting it from AC, and opening the lamp door.

Service guidelines

Roadie 4K35 and 4K45 Service Manual

18

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
16
17
18
19
20
...
»

Содержание Roadie 4K35
























































































Отзывы:

Нет отзывов

Похожие инструкции для Roadie 4K35

Бренд: Marantz Страницы: 2

Бренд: Eiki Страницы: 92

Бренд: Eiki Страницы: 79

Бренд: Christie Страницы: 58

Бренд: Vava Страницы: 18

Бренд: Hitachi Страницы: 87

Бренд: LG Страницы: 61

Бренд: LG Страницы: 38

Бренд: LG Страницы: 2

DX540 - XGA DLP Projector

Бренд: LG Страницы: 40

Бренд: LG Страницы: 54

Бренд: LG Страницы: 92

Бренд: LG Страницы: 74

Бренд: LG Страницы: 59

Бренд: LG Страницы: 52

Бренд: LG Страницы: 104

Бренд: LG Страницы: 126

Бренд: LG Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды