Christie Roadie 4K35 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 87

background image

Maintenance and cleaning

Learn about the information and procedures required for performing projector maintenance. When

performing projector maintenance, obey all warnings and precautions.

Danger! Failure to comply with the following results in death or serious injury.

•

EXTREME BRIGHTNESS! When accessing a restricted access location for product service or
maintenance, avoid exposure to the product beam path by turning the product power off and
disconnecting the product from AC power, or by shuttering the lamp to avoid emissions from the
front aperature.

Warning! Failure to comply with the following could result in death or serious injury.

•

Christie products must be installed and serviced by Christie qualified technicians.

•

Do not operate the product without all of its covers in place.

Ventilation and Cooling

Vents and louvers provide ventilation, both for intake and exhaust, keeping the projector components

within their operating temperature specifications.
Do not install the projector near a radiator, heat register, or within an enclosure. To ensure adequate
airflow, keep a minimum clearance of 50 cm (20 inches) around the projector and never block or cover
the vents.
When replacing fans, ensure you confirm the fan direction for airflow. The correct orientation of the
fan will also ensure that the fan harness reaches the connector.

Inspecting and cleaning the airflow interlocks

Inspect and clean the airflow interlocks to remove accumulated dust or dirt that could impede

movement.
Check: Every 6 months

Warning! Failure to comply with the following could result in death or serious injury.

•

Do not remove or disable the vane switch. Do not attempt to operate the product with
inadequate airflow which can result in dangerous overheating.

Check and clean the lamp blower vane switch, located adjacent to the AC lamp blower in the
igniter compartment.

Inspecting and cleaning the lamp blower

A clogged blower impeller or motor can reduce air flow and lead to overheating and lamp failure.
Check: Every 6 months

Notice. Failure to comply with the following may result in property damage.

•

Do not touch or bend the impeller blades. Do not loosen the balancing weights.

1. Shut down the projector (on page 39).
2. Remove the three screws securing the rear side cover.

Service guidelines

Roadie 4K35 and 4K45 Service Manual

16

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
14
15
16
17
18
...
»

Содержание Roadie 4K35
























































































Отзывы:

Нет отзывов

Похожие инструкции для Roadie 4K35

Бренд: AAXA Technologies Страницы: 2

Бренд: Sim2 Страницы: 60

HQ-Power VDPLPS36B

Бренд: Velleman Страницы: 26

Бренд: Laserworld Страницы: 12

Бренд: BenQ Страницы: 64

Бренд: ACCO Brands Страницы: 38

Бренд: CyberPower Страницы: 2

Бренд: Radio Shack Страницы: 2

Бренд: ViewSonic Страницы: 2

Precision VS11856

Бренд: Precision Страницы: 60

Бренд: Chenzhu Страницы: 2

ACOUSTICS ACU001

Бренд: UPLIFT Страницы: 2

Бренд: Epson Страницы: 91

Бренд: Epson Страницы: 99

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды