Christie Roadie 4K35 Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 87

background image

Optics

Learn how to replace lamps, mirrors, and other optical components.

Removing the lamp

Estimated replacement time: 5 m 10 minute calibration

Danger! Failure to comply with the following results in death or serious injury.

•

Christie products must be installed and serviced by Christie qualified technicians.

•

EXPLOSION HAZARD! Always wear manufacturer approved protective safety clothing (gloves,
jacket, face shield) whenever the lamp door is open or when handling the lamp. Any local or
federal specifications take precedence over Christie's protective clothing recommendations.

•

EXPLOSION HAZARD! Allow sufficient time for the lamp to cool down before powering down the
product, disconnecting it from AC, and opening the lamp door.

Caution! Failure to comply with the following could result in minor or moderate injury.

•

EXPLOSION HAZARD! Handle a lamp by the cathode and anode end shafts only. Do not handle
the lamp by the glass.

Warning! Failure to comply with the following could result in death or serious injury.

•

EXPLOSION HAZARD! Lamps and bare bulbs, even when packaged, may explode if dropped or
mishandled.

•

Christie products must be installed and serviced by Christie qualified technicians.

1. Remove the lamp door (on page 42).
2. Depress the two clips securing the front lamp duct and remove.

3. Loosen the set screw securing the anode (+) lamp connection.
4. Loosen the set screw securing the cathode (-) lamp connection.

Parts and module replacement

Roadie 4K35 and 4K45 Service Manual

60

020-101694-03 Rev. 1 (01-2016)

Copyright

©

2016 Christie Digital Systems USA Inc. All rights reserved.

«
...
58
59
60
61
62
...
»

Содержание Roadie 4K35
























































































Отзывы:

Нет отзывов

Похожие инструкции для Roadie 4K35

Бренд: Nebula Страницы: 12

Бренд: Barco Страницы: 137

Бренд: Optoma Страницы: 4

Бренд: Tripp Lite Страницы: 12

X2 multi-use perfomance

Бренд: InFocus Страницы: 67

Бренд: Lea Страницы: 12

Бренд: Liesegang Страницы: 52

Бренд: Tripp Lite Страницы: 12

Бренд: Eaton Страницы: 12

Бренд: Barco Страницы: 52

Бренд: Hitachi Страницы: 26

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 2

Бренд: Hitachi Страницы: 51

Бренд: Hitachi Страницы: 26

Бренд: Hitachi Страницы: 66

CP-RX80 - XGA LCD Projector

Бренд: Hitachi Страницы: 95

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды