background image

Environmental

China Ministry of Information Industry (along with 7 other Government Agencies) Order No.32
(01/2016) on the control of pollution caused by electronic information products, hazardous
substances concentration limits (GB/T 26572 - 2011), and the applicable product marking
requirement (SJ/T 11364 - 2014).

EU Directive (2011/65/EU) on the restriction of the uses of certain hazardous substances
(RoHS) in electrical and electronic equipment and the applicable official amendment(s).

EU Directive (2012/19/EU) on waste and electrical and electronic equipment (WEEE) and the
applicable official amendment(s).

Regulation (EC) No. 1907/2006 on the registration, evaluation, authorization and restriction of
chemicals (REACH) and the applicable official amendment(s).

International packaging recycling mark requirements.

EU Directive (94/62/EC) on packaging and packaging waste

China packaging recycling mark standard (GB18455-2010)

EU Directive (2012/19/EU) on waste and electrical and electronic equipment (WEEE) and the
applicable official amendment(s).

Regulatory

CP2415-Xe Installation and Setup Guide

47

020-103584-02 Rev. 1 (09-2022)

Copyright 

©

 2022 Christie Digital Systems USA, Inc. All rights reserved.

If printed, please recycle this document after use.

Содержание CP2415-Xe

















































Отзывы: