Chino IR-HA Series Скачать руководство пользователя страница 39

Страница: 39 / 52

INST.No.INE-567-P1CE

-31-

9.1 Initialize Zero/Span Adjustment

This setting is used to initialize zero/span adjustment values.

1) Start zero/span adjustment by push and holding



key,

ENT

key, and

MEASURE

key at the same time while power OFF.

2) Display "init" on the sub display.

3) Push



key or



key to select "on (initialize)" or "oFF (not

initialize)".

4) Registration is completed by pushing

ENT

key.

9.2 Perform Zero/Span Adjustment

Performs zero/span adjustment.
Zero/span adjustment result is reflected to the measured value if
"yES" is set.

1) From zero/span adjustment mode display, push

SEL

key several

times to display "CAL" on the sub display.

2) Push



key or



key to select "yES (perform)" or "no (not

perform)".

3) Registration is completed by pushing

ENT

key.

Remark

Caution

[Initialize Zero/Span
Adjustment display]

CONT

MEM

PEAK

If "on" is selected, all zero/span adjustment values are initialized and return to factory

default.

If "on" is selected, zero/span adjustment result is not reflected to the

measured value.

･

"Init" is display while initializing and key operation is disabled until initialization

completes.

･

Setting of factory default is "oFF".

･

Setting of factory default is "no".

[Zero/Span adjustment display]

CONT

MEM

PEAK

Содержание IR-HA Series





















































Результаты поиска

Содержание IR-HA Series

Отзывы:

Похожие инструкции для IR-HA Series

Бренды по названию

Популярные бренды

Chino IR-HA Series, Инструкция по эксплуатации

Результаты поиска

Содержание IR-HA Series

Отзывы:

Похожие инструкции для IR-HA Series

Бренды по названию

Популярные бренды