Chino IR-HA Series Скачать руководство пользователя страница 33

Страница: 33 / 52

INST.No.INE-567-P1CE

-25-

8. Memory Input Mode (Display/Saving Data)

◆

This is a function of display/saving data.

1) Turn ON the power by holding down

MEASURE

key

2) Push

MEMORY

key on standard measuring mode or continuous measuring mode under "HOLD" status to

start memory input mode.
"

" under main marker "MEM" is lit.

Status flow is shown on the right.
For each setting and selection, refer to the individual
sections.

8.1 Data Display

This setting is used to display data already saved (data number, thermocouple temperature, and emissivity).

1) By push

MEMORY

key on standard measuring mode or

continuous measuring mode under "HOLD" status to make it to
the memory input mode. "

" under main marker "MEM" is

lit.

2) Sub marker "NO" is displayed.
3) Push



key or



key to select data number to display.

4) Blinking stops by pushing

ENT

key and the blinking digit moves

its position from lower place to the higher place and data is
displayed.

5) By pushing

SEL

key, the main marker switches "TC"

(thermocouple temperature indication)

→

"ε"

(emissivity). Perform

procedure 3) to 4) likewise to display thermocouple temperature
and data of emissivity.

Reference

Remark

･

Push

MEMORY

key to end memory input mode.

It returns to standard measuring mode or
continuous measuring mode.

･

It returns to setting mode by pushing and holding

SEL

key.

･

If no key operation has done for 30sec., power

supply is turned OFF automatically.

"no" is displayed if there is no registered data.

Flow Chart

SEL

Data number

Emissivity

Thermocouple

temperature indication

[Data number/thermocouple
temperature/emissivity data
display ]

CONT

MEM

PEAK

Содержание IR-HA Series





















































Результаты поиска

Содержание IR-HA Series

Отзывы:

Бренды по названию

Популярные бренды

Chino IR-HA Series, Инструкция по эксплуатации

Результаты поиска

Содержание IR-HA Series

Отзывы:

Бренды по названию

Популярные бренды