Chino IR-HA Series Скачать руководство пользователя страница 30

Страница: 30 / 52

INST.No.INE-567-P1CE

-22-

7. Measuring Mode

◆

There are two types of measuring method.

[Standard measuring mode] ······ This mode is for portable measurement.

[Continuous measuring mode] ··· This mode is for continuous measurement which this thermometer is

fixed and measuring for a long time at same location.

" under main marker "CONT" is lit.

Status flow is shown below.

For measuring method, refer to the individual sections.

Remark

Warning

If no key operation has done for 30sec. while in "HOLD" state, power supply is turned OFF
automatically.

Never directly sight the objective lens of the thermometer to the sunlight for protecting your eyes

and a detecting element.

・

For the measurement of an object exceeding 1500°C, make sure to turn the beam attenuation

filter switch "ON (attenuation side)" for protecting your eyes.

・

When you feel glare on the measurement of an objects lower than 1500°C, turn the beam

attenuation filter switch "ON (attenuation side)".

(Refer to "4.5 Cautions on Measurement")

◆

Setting Method

Start the thermometer by pushing



key

and push and hold

MEASURE

key while

power OFF.

under main marker "CONT" lights.

◆

Canceling Method

Start the thermometer by pushing



key

and push and hold

MEASURE key

while

power OFF.

under main marker "CONT" turns

OFF.

SEL

Flow Chart

Standard measuring

mode

Highest temperature

indication

Average temperature

indication

Emissivity

Thermocouple

temperature indication

Lowest temperature

indication

Continuous

measuring mode

[In the case thermocouple measurement is set

to "on"]

Push

SEL

key while "HOLD" status to display sub

marker TC.
Thermocouple measurement temperature data is
displayed on the sub display;

･

"oFL" is displayed at 1220°C or more

･

"uFL" is displayed at -50°C or less

*"oFL" is displayed if thermocouple is not
connected.

*Accuracy is not guaranteed for 800°C to
1220°C.

Содержание IR-HA Series





















































Результаты поиска

Содержание IR-HA Series

Отзывы:

Похожие инструкции для IR-HA Series

Бренды по названию

Популярные бренды

Chino IR-HA Series, Инструкция по эксплуатации

Результаты поиска

Содержание IR-HA Series

Отзывы:

Похожие инструкции для IR-HA Series

Бренды по названию

Популярные бренды