Chino IR-HA Series Скачать руководство пользователя страница 24

Страница: 24 / 52

INST.No.INE-567-P1CE

-16-

6.3 Signal Modulation Selection

This setting is used to extract nothing else than average value and maximum value continuously from the
measurement signal (original signal).

1) From setting mode display, push

SEL

key several times to

display "modu" on the sub display.

2) Push



key or



key to select signal modulation.

3) Blinking stops by pushing

ENT

key and the registration is completed.

dELy

It displays the value based on the first order lag of modulation degree set at "6.4.1 Modulation time

constant setting".

PEAk

It displays the value based on the original signal if temperature is rising.

If the temperature is dropping, the value set at attenuation rate setting (refer to the section 6.4.2) is

displayed.

6.4 Modulation Degree Setting

If "dELy" is selected in signal modulation selection, degree of first order lag can be adjusted by setting
modulation time constant.
If "PEAk" in signal modulation selection, signal attenuation degree after tracing peak can be set.

6.4.1 Modulation Time Constant

（

This is only valid if "dELy" is selected for signal modulation

）

1) From setting mode display, push

SEL

key several times to

display "tAu" on the sub display.

2) Numeric value on the main display blinks in the order of

0.0→0.2→0.5→1.0

(sec) when



key is pushed and

0.0→1.0→0.5→0.2

(sec) when



key is pushed.

3) Blinking stops by pushing

ENT

key and the registration is

completed.

Remark

Setting of factory default is "dELy".

Setting of factory default is "0.0"sec.

(Displayed value is based on the

original signal without any modulation).

[Modulation degree
setting display]

CONT

MEM

PEAK

[Signal modulation
selection display]

CONT

MEM

PEAK

Содержание IR-HA Series





















































Результаты поиска

Содержание IR-HA Series

Отзывы:

Бренды по названию

Популярные бренды

Chino IR-HA Series, Инструкция по эксплуатации

Результаты поиска

Содержание IR-HA Series

Отзывы:

Бренды по названию

Популярные бренды