
A U T O M A T IC T R A N S M IS S IO N
7A -97
INTERMEDIATE CLUTCH
INNER SEAL
CENTER SUPPORT
ASSEMBLY
/
ROLLER
ASSEMBLY
V
INTERMEDIATE CLUTCH
RELEASE SPRINGS
TEFLON OIL
SEAL RINGS
\
INTERMEDIATE CLUTCH
SPRING RETAINER
THRUST WASHER
X
INTERMEDIATE CLUTCH
OUTER SEAL
SUPPORT TO
CASE SPACER
INTERMEDIATE
CLUTCH PISTON
INTERMEDIATE CLUTCH
SPRING GUIDE
Fig. 99T--Center Support Assem bly-Exploded View
Inspection
1. Inspect roller clutch inner race for scratches or
indentations. Be sure lubrication hole is open. Be
sure constant bleed plug orifice, (approx. .020 dia.),
is open (fig. 40T).
2. Inspect bushing for scoring, wear or galling. If
replacement is necessary, proceed as follows:
a. Using Tool J-21465-6 with Driver Handle J-8092
remove bushing.
b. From front side of center support, align
elongated slot in the bushing with drilled hole
in the oil delivery sleeve closest to the piston.
Using Tool J-21465-6 and Driver Handle J-8092,
drive bushing squarely into the bore until the
bushing is flush to .010" below top of oil
delivery sleeve.
3. Check oil ring grooves and teflon oil rings for
damage.
NOTE: All service center support oil seal
rings are hook type cast iron.
4. Air check oil passages to be sure they are not inter
connected.
5. Inspect piston sealing surfaces for scratches.
6. Inspect piston seal grooves for nicks or other
damage.
7. Inspect piston for cracks.
8. Inspect release springs for distortion.
9. Inspect support to case for burrs or raised edges. If
present, remove with a stone or fine sandpaper.
Assembly
1. Lubricate and install new inner and outer seals on
piston with lip of seal facing away from spring
pocket (fig. 100T and 10IT).
2. Install inner seal protector, Tool J-21363, on center
support hub, install piston, indexing spring pockets
of piston into cored areas of the center support (fig.
102T).
3. Install intermediate clutch spring guide (Fig.
102TA).
4. Install three (3) release springs into holes of spring
guide. Space equally during assembly (Fig. 102TB).
5. Place spring retainer and snap ring over springs.
6. Compress springs and install snap ring (fig. 103T).
6. Install three (3) hook type cast iron oil seal rings on
the center support if the teflon ring was not
removed. If the teflon ring was removed, install
four (4) hook type cast iron oil seal rings.
7. Air check operation of intermediate clutch piston
(fig. 104T).
OVERHAUL MANUAL
Содержание 10 series 1973
