E N G IN E
6-7
d. Install crankshaft, being careful not to damage
bearing surfaces.
e. Apply a thin coat of brush-on type oil sealing
compound to block mating surface and corre
sponding surface of cap only (fig. 4). Do not
allow sealer on crankshaft or seal lip.
f. Install main bearing caps with arrows pointing
toward front of engine.
g. Torque all except rear main bearing cap bolts to
specifications. Torque rear main bearing cap
bolts to 10-12 ft. lbs. then tap end of crankshaft,
first rearward then forward with a lead hammer.
This will line up rear main bearing and
crankshaft thrust surfaces. Retorque all main
bearing cap bolts to specifications.
h. Measure crankshaft end play with a feeler
gauge. Force crankshaft forward and measure
clearance between the front of the rear main
bearing and the crankshaft thrust surface. Refer
to Figure 42.
2. Install flywheel and torque to specifications. A wood
block placed between the crankshaft and cylinder
block will prevent crankshaft from rotating.
NOTE: Align dowel hole in flywheel with
dowel hole in crankshaft. On vehicles
equipped with automatic transmissions, in
stall flywheel with the converter attaching
pads towards transmission.
3. Install the camshaft as follows:
NOTE: Whenever a new camshaft or new
lifters are installed, lubricate camshaft lobes
and foot of lifters with "Molykote" or its
equivalent.
WITH TIMING CHAIN (V8)
a. Install two 5/16-18 bolts in camshaft bolt holes,
then lubricate camshaft journals with engine oil
and install camshaft, being careful not to
damage bearings (fig. 5). Remove the two 5/16-
18 bolts.
b. Install timing chain on camshaft sprocket then
align marks on camshaft and crankshaft
sprockets and connect chain to crankshaft
sprocket. Align dowel on camshaft with dowel
hole in camshaft sprocket and install sprocket
on camshaft (fig. 6).
Fig. 5—Installing Camshaft
CAUTION:
Do not hammer camshaft sprocket
onto camshaft. This may loosen camshaft rear
expansion plug.
APPLY
SEALANT
TO SHADED
AREAS ONLY
Fig. 4 —Sealing B earing Cap and Block
Fig. 6 —T im in g Sprocket A lig n m e n t M arks
OVERHAUL MANUAL
Содержание 10 series 1973
