
REAR AXLE D IF F ER EN T IA L CARRIER
4 -9
Fig. 12A—Drive Pinion N u t Removal
.003" change in shim dimensions. If backlash
exceeds .008", increase the shim thickness on ring
gear side, while decreasing shim thickness on
opposite side
an equal a m o u n t.
If backlash is less
than .005", decrease the shim thickness on ring gear
side, while increasing shim thickness on opposite
side
an equal am o un t.
DRIVE PINIO N
Removal
1. Remove differential as previously outlined.
2. Check torque required to rotate drive pinion as
described under "Drive Pinion - Installation and
Adjustment". If there is no torque reading, check
for looseness of pinion assembly by shaking (push-
pull) the companion flange. Looseness indicates the
need for bearing replacement.
3. Install Holder J-8614-11 on flange by using two
bolts with flat washers, as shown in figure 12A.
Position J-8614-11 on flange so that the four
notches are toward the flange.
4. Remove pinion nut and washer.
5. Thread end of J-8614-3 into small O.D. end of
J-8614-2. Then with J-8614-11 installed as in step 3,
insert J-8614-2 into J-8614-11 and turn it 1/8 of a
turn to locked position. Remove flange by turning
J-8614-3 while holding J-8614-11 as shown in figure
13A.
6. To remove the drive pinion, first thread the original
pinion nut half way on the pinion, for thread
protection.
7. Place the differential cover temporarily back onto
the housing, using two screws. This will prevent the
pinion from falling to the floor during removal.
8. Tap the end of the pinion nut with a large hammer
and a soft drift, as shown in figure 14A.
NOTE: Care must be taken not to damage
pinion bearings while removing pinion from
carrier. Inspect bearings and cups for damage
and replace if needed.
9. Remove the pinion oil seal and the front pinion
bearing. Remove the cover and retrieve the drive
pinion from the housing. Discard the pinion oil
seal, nut and collapsible spacer. Use a new seal, nut
and spacer on reassembly.
Bearing Removal and Cup Replacement
1. If front pinion bearing is to be replaced, drive
outer race from carrier using a drift in slots
provided for this purpose. Tap alternately on
opposite sides of bearing cup to avoid cocking.
2. If rear pinion bearing is to be replaced, drive outer
race from carrier using a drift in slots provided for
this purpose.
Fig. 13A—Drive Pinion Flange Removal
J- 8 6 14-2
OVERHAUL MANUAL
Содержание 10 series 1973
